background image

10

 

©BRUNO

VSL-6000/6900UK Operator’s  04/16/201

Stop before stitch 

line gets to belt 

guide.

belt guide.

  STEP 5.2

•  Locate the control pendant.

•   Be sure the pendant is not tangled in the lift 

mechanism.

•  Depress and hold the UP switch on the control 

pendant to raise the C-arm/pickup claw high 
enough to avoid catching on something as the 
lift swings out of the vehicle.

•  Release the button.

•  Depress the OUT switch on the control pendant 

to swing the lift arm out of the  vehicle.

NOTE:

  Hold the C-arm/pick-up claw as the lift is 

powered out to  prevent the pick-up device 
from swinging freely and contacting  the 
side of the vehicle.

•  Release the switch when the lift arm is over the 

mobility device.

NOTE:

  Releasing a pendant switch stops lift 

operation.

  STEP 5.3

•  With the lift positioned over the mobility de-

vice, depress and hold the DOWN switch on the 
control pendant.

•  Guide the C-arm/pickup claw to a position slight-

ly below the docking device (installed on the 
mobility device by your dealer).

•  Hook the C-arm/pickup claw onto the docking 

device as shown at the front of this manual.

•  Depress and hold the UP switch on the control 

pendant to lift the mobility device. N

NOTE:

    It may be necessary to raise the 

scooter until the C-arm/pickup claw is 
approximately 1” (25 mm) below the belt 
guide.

•  Release the switch before the white stitching on 

the belt reaches the belt guide.

Содержание Curb-Sider VSL-6000

























Отзывы: