manualshive.com logo in svg

Bruker NMR iProbe HR-Liquids, Руководство пользователя, Страница: 25 / 56

Поделиться
Скачать
Bruker NMR iProbe HR-Liquids Скачать руководство пользователя страница 25

Installation

Z33146_1_001

25 / 56

The installation of the iProbe HR-Liquids is complete and the iProbe HR-Liquids can be
detected by the software with the command 

edprobe

.

6.2.2

Installation of iProbe HR-MAS

NOTICE

In the iProbe HR-MAS the bearing gas has two functions: supporting the rotor for spinning
and regulating its temperature. There is no dedicated VT gas flow unless the probe is
specified as DVT. In this last case, the setup of the VT GAS is analogous to the iProbe HR-
liquids.

The following instructions are intended for non-DVT probes only.

Prerequisite: The quick-lock is mounted to the
lower part of the shim system according to the

Quick-Lock Mounting Instruction

 

(Z166745).

• Take the iProbe HR-MAS out of the

transport box and remove the protection
cap.

• Check that the quick lock lever is in the

unlock position.

• Slide the iProbe HR-MAS into the magnet.

Mount the iProbe so that the clip holders
(1) on the iProbe body fit exactly the holes
for the clip holders in the quick-lock so that
the iProbe is in the correct orientation.

• Lock the iProbe HR-MAS in the position

using the quick-lock lever.

Connections at the rear side:

• Remove the white plastic cover and

connect the Johnston connector of the VT-
gas hose or the BCU to the rear side of the
iProbe HR-MAS.

• Mount the support clamp (Z53660) on the

magnet as shown in the photo. Position
and support the transfer line using the
Velcro tape of the support clamp.

Содержание NMR iProbe HR-Liquids

























































Отзывы:

Нет отзывов