Bruker NMR 400 89 Ascend DNP Скачать руководство пользователя страница 23

Страница: 23 / 106

ZTKS0243 / Z31993 / 03

Safety

Transportation

CAUTION

Risk of injury and property damage due to incorrect transportation.

The boxes may tilt, movement may get out of control. Thus persons may get injured
and the c

ontents

or further equipment may be damaged.

Thus:

• Be careful while unloading and moving the boxes.

• Do not move the boxes arbitrarily.

• Pay attention to all symbols on the boxes.

• Pay attention to sharp edges and spikes of boxes and parts by using protective

gloves while moving.

• Move the boxes in an upright position.

• Do not tilt the boxes.

• Prevent crossing thresholds, even if they are only a few millimeters high.

• Clean the transportation way before moving the box.

• Unpack shortly before assembling.

• The c

ontents

or further equipment must be protected from rain and other bad

weather conditions during transportation.

• Exclusively move the cryostat in its original box.

• Do not remove the tightening straps inside the box until assembling.

• Only use the provided attachment points.

• Ensure that the cryostat is always leveled during any transportation.

• Transportation only with attached transportation locks.

• Do not move the evacuated cryostat.

• Do not move the cryostat after cool down.

Содержание NMR 400 89 Ascend DNP











































































































Результаты поиска

Содержание NMR 400 89 Ascend DNP

Отзывы:

Похожие инструкции для NMR 400 89 Ascend DNP

Бренды по названию

Популярные бренды

Bruker NMR 400 89 Ascend DNP, Руководство пользователя

Результаты поиска

Содержание NMR 400 89 Ascend DNP

Отзывы:

Похожие инструкции для NMR 400 89 Ascend DNP

Бренды по названию

Популярные бренды