Brother P-Touch 580C Скачать руководство пользователя страница 129

Страница: 129 / 188

125

PROBLEM

REMEDY

1. The display stays blank after you have
turned on the machine or abnormal cha-
racters are displayed.

•

Check that the AC adaptor is attached

properly.

•

If you are using alkaline batteries, check

that they are properly inserted.

•

If the batteries are low, replace them.

•

Hold down

CODE

and

keys and press

the

ON/OFF

key twice to reset the mac-

hine. The display and all contents of the
memory are also deleted.

2. The machine does not print or the printed
characters are blurred.

•

Check that the tape cassette has been

inserted properly.

•

If the tape cassette is empty, replace it

with a new one.

•

Make sure that the tape cassette cover

has been closed.

3. The printed characters are not formed
properly.

•

If you are using alkaline batteries, they

may be low. Try using the AC adaptor.

4. Striped tape appears.

•

You have reached the end of the tape.

Replace it with a new tape.

5. In multi-color print mode, the tape cannot
be fed after the machine’s power supply
was suddenly cut (e.g. the power button
was pressed or there was a power failure)
while rewinding the tape, which caused
the rewinding gear to remain engaged.

•

Open the tape compartment cover, re-

move the multi-color tape cassette, then
close the cover.
Turn on the power and press the

FEED

key to disengage the rewinding gear,
causing the message “NO TAPE!” to be
displayed.

Содержание P-Touch 580C





























































































































































































Результаты поиска

Содержание P-Touch 580C

Отзывы:

Похожие инструкции для P-Touch 580C

Бренды по названию

Популярные бренды

Brother P-Touch 580C, Руководство пользователя

Результаты поиска

Содержание P-Touch 580C

Отзывы:

Похожие инструкции для P-Touch 580C

Бренды по названию

Популярные бренды