Brother B-500 Скачать руководство пользователя страница 142

Страница: 142 / 211

Test Mode

4 - 4

Test mode list

Mode

Test mode

No.

Z (zigzag) operations

F (feed)

operations

Operation

speed

Adjustment used

Referen
ce page

3 point needle drop

Whenever the Reverse
stitch button is pushed,
needle position is
switched to left base
line / center base line /
right base line.

None

It is freely
changed with
the Sewing
speed
controller

Three point needle
drop adjustment

4 - 8

Clearance between
the needle and the
rotary hook point
adjustment

4 - 10

Needle bar rise
adjustment

4 - 11

Needle bar height
adjustment

4 - 12

Needle interference
left/right adjustment

4 - 13

Forward and reverse
feed

100 stitches forward on the left base
line
100 stitches reverse on the right base
line

It is freely
changed with
the Sewing
speed
controller

Feed adjustment

4 - 17

Feed dog position

Front/back, left/right
position of feed dog
adjustment

4 - 21

Содержание B-500




















































































































































































































Результаты поиска

Содержание B-500

Отзывы:

Бренды по названию

Популярные бренды

Brother B-500, Руководство по обслуживанию

Результаты поиска

Содержание B-500

Отзывы:

Бренды по названию

Популярные бренды