Brother B-500 Скачать руководство пользователя страница 126

Страница: 126 / 211

3 - 55

Feed and bobbin module

Modules

Attachment of Feed adjuster assy.

1. Insert the polyester slider

and the spring

into the shaft of the feed

adjuster assy.

*Key point

• Insert the spring starting with the side having the smaller

spring diameter.

2. Attach the feed adjuster assy.

to the base plate assy.

Lubricate the feed adjuster shaft with FBK OIL RO
100.

1-2 drops

XC8388***

Apply EPNOC AP (N) 0 to the entire operating
part of the feed adjuster feed regulator slide block.

Small amount

XC8387***

S10

SPRING

XC2531***

8.8

9.9

5.5

1-1

Assembly of Feed adjuster assy.

1. Attach the F gear

to the feed adjuster

*Key point

• When set it as shown in the right figure, check that the

protrusion

of the F gear

is the upper side.

2. Attach the spring

Apply EPNOC AP (N) 0 to the entire operating
surface of the feed adjuster and F gear.

Small amount

XC8387***

S11

15.1

SPRING

XC2530***

Содержание B-500




















































































































































































































Результаты поиска

Содержание B-500

Отзывы:

Бренды по названию

Популярные бренды

Brother B-500, Руководство по обслуживанию

Результаты поиска

Содержание B-500

Отзывы:

Бренды по названию

Популярные бренды