manualshive.com logo in svg

Brother 9840CDW - Color Laser - All-in-One, Руководство пользователя

Поделиться
Скачать
Brother 9840CDW - Color Laser - All-in-One Скачать руководство пользователя страница 151

Troubleshooting and routine maintenance

135

C

Document Jam

The document was not inserted 
or fed properly, or the document 
scanned from the ADF was too 
long.

See 

Document jams

on page 140 or 

Using the 

ADF (automatic document feeder)

on page 20.

DR Mode in Use

The machine is set to Distinctive 
Ring mode. You cannot change 
the Receive Mode from Manual to 
another mode.

Set Distinctive Ring to 

Off

. (See 

Turning off 

distinctive ring

on page 53.)

Drum Error

The corona wires on the drum 
unit needs to be cleaned.

Clean the four corona wires on the drum unit. 
(See 

Cleaning the corona wires

on page 158.)

EL Error

The machine has a mechanical 
problem.

Open the front cover and close it again.

Fuser Error

The temperature of fuser unit 
does not rise at a specified 
temperature within specified time.

Turn the power switch off, wait a few seconds, 
and then turn it on again. Leave the machine for 
15 minutes with the power on. The machine can 
be turned off for up to 4 days without losing faxes 
stored in the memory. (See 

Checking if the 

machine has faxes in its memory

on page 139.)

The fuser unit is too hot.

Init Unable XX

The machine has a mechanical 
problem.

Turn off the machine’s power switch and then 
turn it on again. If the error message continues 
leave the machine for several minutes and then 
try to print, copy or scan again. The machine can 
be turned off for up to 4 days without losing faxes 
stored in the memory. (See 

Checking if the 

machine has faxes in its memory

on page 139.)

Jam Duplex

The paper is jammed in the 
duplex tray.

(See 

Paper jams

on page 141.)

Jam Rear

The paper is jammed in the back 
of the machine.

(See 

Paper jams

on page 141.)

Jam Inside

The paper is jammed inside the 
machine.

(See 

Paper jams

on page 141.)

Jam MP Tray

The paper is jammed in the MP 
tray of the machine.

(See 

Paper jams

on page 141.)

Jam Tray 1

Jam Tray 2

The paper is jammed in the paper 
tray of the machine.

(See 

Paper jams

on page 141.)

Low Temperature

The temperature of the machine 
is too cold.

Increase room temperature to allow the machine 
to operate.

No Belt Unit

The belt unit is not installed.

Install the belt unit. (See 

Replacing the belt 

unit

on page 183.)

No Drum Unit

The drum unit is not installed.

Install the drum unit. (See 

Replacing the drum 

unit

on page 177.)

No Paper

The machine is out of paper or 
paper is not properly loaded in the 
paper tray.

Do one of the following:

„

Refill the paper in the paper tray or MP tray.

„

Remove the paper and load it again.

Error Message

Cause

Action

Содержание 9840CDW - Color Laser - All-in-One










































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды