Brother Industries SUPER ACE+e Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 56

background image

-35-

12.

POSITION OF BUTTONHOLE SWITCH LEVER

STANDARD

When the buttonhole lever is lowered, the clearance of front part of buttonhole foot is 1.5 mm and the presser
foot lever is lowered BH 0 should touch BH 1.

ADJUSTMENT

1.

Turn on power switch and select pattern .

2.

Fit the buttonhole foot (A). Adjust the clearance to 1.5 mm, and lower the presser foot lever.

3.

Adjust the position of buttonhole lever so that BH0 touches BH1 when the buttonhole eccentric shaft is
rotated.
NOTE :In case that the legs are shorter than the standard, bend the BH 1 to be far from BH 0.

In case that the legs are longer than the standard, bend the BH 2 to be close to BH 0.

Adjustment Point

If the buttonhole eccentric shaft (C) is rotated clockwise, the clearance (D) between BH0 and BH1 widens.

Pull open the buttonhole foot to its maximum and check that the switch can be switched.

www.promelectroavtomat.ru

«
...
35
36
37
38
39
...
»

Содержание SUPER ACE+e

























































Отзывы:

Нет отзывов

Похожие инструкции для SUPER ACE+e

Бренд: SYSFORM Страницы: 28

Industrial Floor Stripper

Бренд: Samurai Страницы: 28

Бренд: handi quilter Страницы: 69

hammerhead 1100srx

Бренд: Bortek Страницы: 74

Бренд: Cognex Страницы: 31

Sweepmaster B1200 RH

Бренд: HAKO Страницы: 64

Бренд: Radio Shack Страницы: 24

Бренд: Tivax Страницы: 6

Advolution UHR 70-1700

Бренд: Nilfisk-Advance Страницы: 32

Бренд: JUKI Страницы: 59

Бренд: CleanStar Страницы: 9

Бренд: Panasonic Страницы: 25

Бренд: Panasonic Страницы: 56

Бренд: Panasonic Страницы: 60

Бренд: Panasonic Страницы: 69

Бренд: Panasonic Страницы: 68

Бренд: Panasonic Страницы: 72

Бренд: Panasonic Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды