Brooks 0254 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 124

background image

3-20

Model 0254

Section 3 Operation

Installation and Operation Manual

X-SE-0254-eng

Part Number: 541B129AAG

September, 2010

3-6-4-1 Blend Control Setup

Program the above values for master and slave channels desired to
perform blending.

Select Blend Master

From the home screen, point to a channel desired to be the master and
press the

master blend key. This causes the home screen to show an

‘M,’ indicating master channel. If you press the master key again at that
moment, the ‘M’ control indicator will no longer be present—no master is
then selected—and blending will not be conducted.

To de-select a blend master, point to the present master channel and press
the

master blend key. Note that the ‘M’ control indicator is no longer

present and the master has been de-selected.

Home Screen

Master Channel Setup

It is recommended that you wait until after the blending setup is complete
before selecting the desired flow rate setpoint to the Master Channel (refer
to "3-6-4-2 Start Blend" on p. 3-21).

To configure the Master Channel for blending:

1. Position the cursor pointing towards the appropriate channel on the

Home screen.

2. Press the ENTER/MENU key.

3. Select Instrument Configuration by pressing the ENTER/MENU key.

4. Once in the Instrument Configuration screen, scroll down to the SP

Function option and select Rate.

5. Scroll down to the SP Rate option and input a zero flow rate setpoint (or

via the Setpoint hot key).

NOTE: If you input a flow rate setpoint other than zero, the Master Channel will
immediately respond to that setpoint and will start to flow.

«
...
44
45
46
47
48
...
»

Содержание 0254





























































































































Отзывы:

Нет отзывов

Похожие инструкции для 0254

Бренд: Raycus Страницы: 40

Бренд: RaycoWylie Страницы: 31

Бренд: Kawai Страницы: 8

GroundCast DRS611

Бренд: Vaisala Страницы: 12

Бренд: Aethra Страницы: 2

Бренд: Flymaster Страницы: 7

Бренд: SecureAlert, Inc. Страницы: 7

Бренд: GANN Страницы: 89

Бренд: Cal Test Electronics Страницы: 12

Бренд: C.R. Laurence Страницы: 4

Бренд: Neogen Страницы: 9

Бренд: TE Connectivity Страницы: 3

Rangemaster CRF 1000

Бренд: Leica Страницы: 118

Бренд: SloanLED Страницы: 3

Бренд: Barco Страницы: 33

Бренд: Bender Страницы: 4

Бренд: TEKELEK Страницы: 3

Бренд: South Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды