BRONKHORST Mini CORI-FLOW MI Series страница 44 Скачать руководство пользователя

Страница: 44 / 53

Bronkhorst®

Instruction Manual MI Series Industrial mini CORI-FLOW™

9.17.120A

Technical information

5.1

Model key

The model key on the serial number label contains information about the technical properties of the instrument as ordered.

The actual properties of your instrument can be retrieved with the diagram below.

5.2

Customized I/O options

mini CORI-FLOW™ instruments can offer several customized input/output functions as an option. These options can be

installed on the M8 wire of the Main terminal and on the A2 wire of the Actuator terminal (see section

Electrical connection

I/O options are factory installed as specified at ordering time, and cannot be changed manually.

The

model key

on the serial number label contains information about the I/O configuration of your instrument. The

possible configurations are described in the table below. Consult the hook-up diagram for custom bus and I/O

configurations for an explanation of the codes.

Code

Description

000

Disabled, M8/A2 is pulled down to 0Vdc (default selection)

A1V

0…10Vdc sourcing output, controller

Analog signal for pump or external valve steering (control signal only)

When the controller output is used for pump or external valve steering (mass flow meters only), make sure

to set parameter

Valve maximum

to 0.3 [A]. For mass flow controllers, the controller output is limited to a

value below 10Vdc, due to the maximum valve current restriction.

B1V

4…20mA sourcing output, controller

Analog signal for pump or external valve steering (control signal only).

When the controller output is used for pump or external valve steering (mass flow meters only), make sure

to set parameter

Valve maximum

to 0.3 [A]. For mass flow controllers, the controller output is limited to a

value below 20mA, due to the maximum valve current restriction.

Содержание Mini CORI-FLOW MI Series






















































Результаты поиска

Содержание Mini CORI-FLOW MI Series

Отзывы:

Похожие инструкции для Mini CORI-FLOW MI Series

Бренды по названию

Популярные бренды

BRONKHORST Mini CORI-FLOW MI Series, Инструкция по эксплуатации

Результаты поиска

Содержание Mini CORI-FLOW MI Series

Отзывы:

Похожие инструкции для Mini CORI-FLOW MI Series

Бренды по названию

Популярные бренды