background image

MASS-STREAM

TM

 Instruction Manual D-6200 

9.17.112A – Date of issue: 2017-03 

Page 4 off 12 

Table of Contents 

 

 

1  ANALOG INSTRUMENTS....................................................................................... 5

 

1.1  General.................................................................................................................... 5 
1.2  Installation............................................................................................................... 7 
1.3  Operation and Maintenance.................................................................................. 8 
1.4  Specifications of analog MASS-STREAM

TM

 Instruments D-6200………….…... 9 

1.5  Hook-up with 6DIN Connector, 6-pin round....................................................... 10 
1.6  Hook-up with 15-pin sub-D connector……......................................................... 10

 

 

2  CTA MEASUREMENT PRINCIPLE……………………………................................11 

 

 
 
The dimensional drawings and hook-up diagram of the Mass-Stream

TM

 instruments 

D-6200 are available for download on our website www.mw-instruments.com. 

 

 

Содержание MASS-STREAM D-6200













Отзывы: