BRONKHORST EL-PRESS Metal sealed Скачать руководство пользователя

Страница: 31 / 45

Bronkhorst®

Instruction Manual EL-PRESS™

9.17.101I

4.1

Special parameters

Init Reset

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char

82/64

0/10

0x000A/11

Init Reset

is used to unlock secured parameters (marked with a



symbol) for writing. It supports the following values:

Value

Description

unlocked, secured parameters can be read and written to

locked, secured parameters are read-only

At power-up,

Init Reset

is always set to ‘Locked’ (value 82).

Reset

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char

0…7

114

115/8

0x0E68/3689

This parameter is used to reset the program, counter or alarms.

Value

Description

No reset

Reset counter

Reset alarm

Reset counter

Reset and disable counter

Reset firmware program (soft reset)

Reset

Alarm info

error bit

Reset

Alarm info

warning bit

The

Reset

parameter may be disabled by

Reset Alarm Enable

Reset Counter Enable

. Make sure the value is accepted

by sending value 0 first.

Wink

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char [27]

0…9*

0/0

0x0000/1

Sending any text string value between 1 and 9 to this parameter makes the indication LEDs (if present) blink for a couple of

seconds. This can be useful in order to identify a specific device in a large fieldbus network.

*) Modbus only supports value 14592

Control Mode

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned int

0…255

1/4

0x0024/37

Control Mode

is used to select different control modes of the instrument and determines from which source(s) it accepts a

setpoint. The following control modes are available:

Value

Mode

Instrument action

Setpoint source

BUS/RS232

Controlling

Fieldbus/RS-232

Analog Input

Controlling

Analog input

FLOW-BUS Slave

Acting as slave instrument on FLOW-BUS

RS-485 only: FLOW-BUS

master output x

Slave

Factor/

100%

Valve Close

Controller disabled, valve closed

Controller Idle

Controller disabled, valve frozen in current position

Содержание EL-PRESS Metal sealed














































Результаты поиска

Содержание EL-PRESS Metal sealed

Отзывы:

Похожие инструкции для EL-PRESS Metal sealed

Бренды по названию

Популярные бренды

BRONKHORST EL-PRESS Metal sealed, Инструкция по эксплуатации

Результаты поиска

Содержание EL-PRESS Metal sealed

Отзывы:

Похожие инструкции для EL-PRESS Metal sealed

Бренды по названию

Популярные бренды