background image

Bronkhorst®

Instruction Manual EL-FLOW® Classic series

9.17.085D

13

3.3

Multifunctional switch

Some special functions of the instrument can be started manually using the multifunctional switch near the indication

LEDs.

3.3.1

Normal operating functions

·

In order to access these functions, press and hold the switch while the instrument is in normal operation mode (green

LED glowing).

·

As long as the switch is held, the LEDs show a repeating sequence of patterns, where each pattern indicates a function.

·

All indications in this sequence are continuous.

·

Each pattern is shown for a number of seconds; in the table below the column 

Hold time

 indicates the time frame within

the sequence where the LEDs show the associated pattern.

·

To start a function, release the switch when the LEDs show the pattern of the required function.

(green)

(red)

Hold time Function

off

off

0…4 sec

No action

off

on

4…8 sec

Reset instrument; clear all warnings and error messages and restart the instrument

on

off

8…12 sec Auto-zero; re-adjust the zero-point of the instrument (flow meters/controllers)

on

on

12…16 sec Factory mode, do not use

See 

Zeroing before use

 for background information and instructions on how to adjust the zero point of an instrument.

Never perform a zeroing procedure before having taken notice of the instructions.

3.3.2

Power-up functions

·

In order to access these functions, press and hold the switch while powering up the instrument.

·

As long as the switch is held, the LEDs show a repeating sequence of patterns, where each pattern indicates a function.

·

All indications in this sequence are flashing (0.2 sec on, 0.2 sec off).

·

Each pattern is shown for a number of seconds; in the table below the column 

Hold time

 indicates the time frame within

the sequence where the LEDs show the associated pattern.

·

To start a function, release the switch when the LEDs show the pattern of the required function.

(green)

(red)

Hold time Function

off

off

0…4 sec

No action

off

on

4…8 sec

Restore factory settings (All parameter settings will be restored)

on

off

8…12 sec No action

on

on

12…16 sec Factory mode, do not use

Содержание EL-FLOW Classic Series



















Отзывы: