Bromic Heating ECLIPSE SMART-HEAT ELECTRIC 3400W Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 28

Bromic Heating ECLIPSE SMART-HEAT ELECTRIC 3400W Скачать руководство пользователя страница 28

28

bromic.com/heat

TROUBLESHOOTING

REPLACEMENT PARTS

SYMPTOM

POSSIBLE CAUSE (S)

CORRECTIVE ACTION

No heat

1. Incorrect heater setting chosen
2. Incorrect Voltage.
3. No power.
4. No/low batteries in remote.
5. Remote too far.
6. Radio interference.
7. Remote not paired or faulty
control.

1. Choose heat setting using
remote (33%, 66% or 100%).
2. Connect to 220-240V power supply.
3. Check connection to power supply.
4. Change remote batteries.
5. Move remote closer to heater.
6. Move remote closer to heater,
  disable other radio emitting devices.
7. Pair remote to heater PCB.

Not enough heat

1. Incorrect heater setting chosen.
2. Heater too small for application.

1. Choose higher heat setting
using remote (66% or 100%).

2. Add additional heater(s).

Too much heat

1. Incorrect heater setting chosen.

1. Choose lower heat setting
using remote (66% or 33%).

No Light

1. Incorrect lighting setting chosen.
2. Incorrect Voltage.
3. No power.
4. No/low batteries in remote.
5. Remote too far.
6. Radio interference.
7. Remote not paired or faulty
control.

1. Choose lighting setting using
remote (50% or 100% (DIM^)).
2. Connect to 220-240V power supply.
3. Check connection to power supply.
4. Change remote batteries.
5. Move remote closer to heater.
6. Move remote closer to heater,
  disable other radio emitting devices.
7. Pair remote to LED PCB.

Not enough Light

1. Incorrect lighting setting chosen.

2. Light too small for application.

1. Choose higher lighting setting
using remote (50% or 100% (DIM^)).

2. Add additional light(s).

Too much Light

1. Incorrect lighting setting chosen.

1. Choose lower heat setting
using remote (50% or OFF (DIM^)).

Part Number

Description

Part Number

Description

BH0820011

Eclipse Electric Portable
Heater Head (EU)

BH8380025

Mains Cable (EU)(16A) for
Eclipse Electric Portable

BH8380021

Eclipse Electric Portable
Arms Assembly

BH8380026

Screw & O-Ring Set
Portable Eclipse

BH8380022

Eclipse Electric Portable
Base Assembly (EU)

BH8380027

Portable Control Box (EU)
for Eclipse Electric Portable

BH8380023

Base Top Cover for Eclipse
Electric Portable

BH8380028

Base Weight (10 kg) for
Eclipse Electric Portable

BH8380024

Base Wheels Set (2) for
Eclipse Electric Portable

BH8380031

Remote Control for Eclipse
Electric Control (EU)

«
...
26
27
28

Содержание ECLIPSE SMART-HEAT ELECTRIC 3400W





























Отзывы:

Нет отзывов