Broco PC/A-5V2HR Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 49

background image

3-5. RESTART PROCEDURES.

a. If at any time the cutting rod goes out while in use, move the torch away from the cutting surface.

Check the oxygen flow and pressure and then re-ignite the rod as previously explained. If re-
ignition fails or the rod continues to go out, insert a new rod and ignite the rod as previously
explained.

Cutting rod is considered consumed when less than two inches long. Never allow a cutting rod to
burn into the torch. Never use a damaged cutting rod.

b. Cutting rods may also seal shut during use, especially if the oxygen flow is stopped before

removing the rod from the work piece. To clear a sealed rod when using a striker plate and battery,
touch the rod tip to the striker plate and depress the oxygen control lever when the arcing begins.
This procedure may have to be repeated to completely clear the rod.

c. If a rod becomes sealed when using the RapidFire cutting rod igniters, a new rod must be

inserted and ignited with the rod igniter as previously explained.

3-6. SHUTDOWN PROCEDURES.

a. Release the oxygen control lever to stop the rod from burning.

b. Loosen the collet nut and remove the rod from the torch assembly then close the oxygen cylinder

valve.

c. Depress the oxygen control lever to relieve any pressure from the oxygen hose and the pressure

gauge/hose.

Always place a protective cap or piece of tape over the open end of the
oxygen hose to prevent dirt or foreign objects from entering during storage.

d. Disconnect and remove the oxygen hose from the regulator at the quick disconnect fitting.

e. Unsnap the snap tabs on the back harness assembly and remove the regulator and pressure

gauge/hose from the oxygen cylinder. Inspect the inlet nipple on the regulator (not shown) for
damage and/or wear.

f.

Disconnect and remove the black power cable electrical connector from the lightweight battery.

g. Disconnect and remove the red striker plate electrical connector from the lightweight battery.

h. Wipe down the torch assembly and striker plate assembly with a clean, oil-free cloth.

i.

Remove the collet nut, collet, collet washer, flash arrestor, and flash arrestor screen from the torch.
Inspect for damage and/or wear. Clean and reassemble.

«
...
32
33
34
35
36
...
»

Содержание PC/A-5V2HR


















































Отзывы:

Нет отзывов

Похожие инструкции для PC/A-5V2HR

Бренд: Esko Страницы: 133

Бренд: Stihl Страницы: 260

Бренд: Land Pride Страницы: 94

Бренд: START International Страницы: 17

WAZER Main Unit

Бренд: Wazer Страницы: 69

Бренд: RAIMONDI Страницы: 32

Бренд: Meec tools Страницы: 112

Бренд: Milescraft Страницы: 8

SignCrafter 1206

Бренд: Milescraft Страницы: 16

Бренд: Laski Страницы: 40

Бренд: RASOR Страницы: 12

Бренд: Felder Страницы: 104

Бренд: KURIS Страницы: 40

Бренд: Raider Страницы: 38

Бренд: RASOR Страницы: 15

Бренд: Zenoah Страницы: 22

Бренд: NARGESA Страницы: 29

Бренд: Strongway Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды