manualshive.com logo in svg

Brocade Communications Systems DCX 8510-8, Справочник по аппаратуре

Поделиться
Скачать
Brocade Communications Systems DCX 8510-8 Скачать руководство пользователя страница 131

Diagnostics and Troubleshooting

● 

Introduction................................................................................................................... 131

● 

Obtaining chassis and component status..................................................................... 131

● 

Interpreting POST and boot results...............................................................................132

● 

Diagnostics....................................................................................................................133

● 

Troubleshooting............................................................................................................ 134

Introduction

For information about troubleshooting the entire fabric, refer to the 

Fabric OS Troubleshooting and

Diagnostics Guide.

The Brocade DCX 8510-8 includes a number of diagnostic aids to assist with troubleshooting, including
LEDs on the hardware, commands that display current status, diagnostic tests for hardware and
software, and error messages. In addition, a number of managing and monitoring features are available,
such as Fabric Manager, Web Tools, Fabric Watch, and Advanced Performance Monitoring.

If the Brocade DCX 8510-8 does not operate as expected, the following steps can be taken to diagnose
the problem:

• Check the LEDs and refer to the LED tables (

Monitoring System Components

 on page 49) for

interpretation and recommended actions.

• Review the results of the last POST run by the Brocade DCX 8510-8 (

Interpreting POST and boot

results

 on page 132).

• Review the error logs. (Refer to the 

Fabric OS Troubleshooting and Diagnostics Guide

 for more

information).

‐

Review RASlog entries.

‐

Use the 

sensorShow

 command to determine the status of the hardware components.

‐

Run diagnostic tests (

Diagnostics

 on page 133).

‐

Reboot the Brocade DCX 8510-8 or power the entire chassis off and then on (

Powering off

the Brocade DCX 8510-8

 on page 48 and 

Providing power to the Brocade DCX 8510-8

Backbone

 on page 27).

If the problem is still unresolved after these steps, contact your support provider.

Obtaining chassis and component status

The CLI commands in the following table provide status and environmental information about the
chassis and its components. These commands provide information only, and they do not interrupt traffic
flow. For more information about these commands, refer to the 

Fabric OS Command Reference.

Brocade DCX 8510-8 Backbone Hardware Reference Manual

131

53-1002180-08

Содержание DCX 8510-8

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды