Brocade Communications Systems DCX 8510-8 Скачать руководство пользователя страница 132 | Manualshive

Страница: 132 / 176

background image

Environmental status and maintenance commands

TABLE 17

Command

Information displayed

sensorShow

Temperature readings for the port blades

Temperature readings for the CP blades

Status and RPM of all operational fans

Status of all operational power supplies

tempShow

Temperature readings for the port blades

Temperature readings for the CP blades

psShow

Status of all operational power supplies

fanShow

Status and RPM of all operational fans

chassisShow

Serial number, time awake, and additional information about each component

slotShow

Slot occupancy

errShowerrDump

System error log. Refer to the

Fabric OS Message Reference

for more information on the

messages in this log.

Interpreting POST and boot results

The Brocade DCX 8510-8 performs Power-On Self-Test (POST) by default each time the chassis is
powered on, rebooted, or reset. The Brocade DCX 8510-8 can be rebooted using the

reboot

(to

reboot each CP individually) or

fastBoot

commands. The

fastBoot

command reboots the switches

without running POST. If the active CP blade is rebooted, it fails over to the standby CP blade.

POST

The Brocade DCX 8510-8 automatically performs POST each time it is powered on or reset.

To verify that POST has completed without error, do the following:

• Verify that all LEDs return to a normal state after POST completes.

If one or more LEDs do not return to a normal state, and this is not due to the Brocade DCX 8510-8
being set to beacon, refer to the relevant LED table to identify and correct the problem. For port
blades, and CP and core switch blades, the

slotShow

command can be used to check the status of

the slots. For information about turning beaconing on or off, refer to the

Fabric OS Administrator's

Guide

.

• Verify that the switch prompt displays when POST completes.

If it does not display, POST was not successfully completed. Contact the Brocade DCX 8510-8
supplier for support.

• Review the system error log using the

errShow

or

errDump

commands.

Interpreting POST and boot results

132

Brocade DCX 8510-8 Backbone Hardware Reference Manual

53-1002180-08

«
...
130
131
132
133
134
...
»

Содержание DCX 8510-8

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DCX 8510-8

eServer BladeCenter JS20 Type 8842

Бренд: IBM Страницы: 150

Бренд: Inspur Страницы: 82

Бренд: TYAN Страницы: 106

Бренд: Thecus Страницы: 120

Бренд: IBM Страницы: 100

Бренд: LOVATO ELECTRIC Страницы: 5

Бренд: EVS Страницы: 198

DIRECTORY SERVER 8.0

Бренд: Red Hat Страницы: 128

9000 APPLIANCE SERIES

Бренд: Arcserve Страницы: 14

Бренд: Silicon Graphics Страницы: 30

Бренд: Planet Страницы: 108

SecureBox SDS1100

Бренд: Lantronix Страницы: 75

Бренд: Gigabyte Страницы: 127

DiskStation DS110+

Бренд: Synology Страницы: 11

Бренд: FieldServer Страницы: 11

Бренд: Oracle Страницы: 274

Бренд: Gigabyte Страницы: 67

Бренд: hager Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды