12
Do:
• Regularly wash with clean cloth or rag soaked with warm water
and mild soap or liquid dish detergent.
• Always clean in the direction of original polish lines.
• Always rinse well with clear water (2 or 3 times) after cleaning.
Wipe dry completely.
• You may also use a specialized household stainless steel
cleaner.
Don’t:
• Use any steel or stainless steel wool or any other scrapers to
remove stubborn dirt.
• Use any harsh or abrasive cleansers.
• Allow dirt to accumulate.
• Let plaster dust or any other construction residues reach the
power pack. During construction or renovation, cover the power
pack to make sure no dust adheres to stainless steel surface.
21. USE AND CARE
(CONT'D)
Power Pack Cleaning
Stainless steel cleaning
:
Avoid when choosing a detergent:
- Any cleaners that contain
bleach
will attack stainless steel.
- Any products containing:
chloride, fluoride, iodide, bromide
will deteriorate surfaces rapidly.
- Any combustible products
used for cleaning such as
acetone, alcohol, ether, benzol
, etc., are highly explosive and should never be
used close to a range.
22. OPERATION
!
WARNING
When using a gas stove, always turn the power pack blower(s) on prior to begin cooking. In addition, the blower(s)
must be at least in third speed if three burners or more are turned on simultaneously. Failure to do so may lead the
surface of the power pack to become very hot.
Always turn your power pack on before you begin cooking to establish an air flow in the kitchen. Let the blower run for a few minutes to
clear the air after you turn off the range. This will help keep the whole kitchen cleaner and brighter.
HC0023
A
B
C
D
A. D
ELAY
SWITCH
:
When a blower speed is selected, press this switch to activate the delay function. The corresponding blower speed switch will flash to
indicate this function is activated. The blower will continue to operate for 5 minutes and will stop automatically. To cancel the delay
function, press the delay switch once again.
B. S
TART
/S
TOP
/S
PEED
S
ELECTION
S
WITCHES
:
Press the switch corresponding to the desired blower speed (from
1
for low speed to
4
for high speed). The chosen switch will light. To
turn off the blower, press once more on the corresponding blower speed switch; the switch light will shut off.
NOTE: When blower is off, pressing on blower speed
1
switch will cause the blower to start on high speed for a very short lapse of time,
and then resume on speed
1
.
C. M
ASTER
OFF/F
ILTER
MAINTENANCE
/H
EAT
S
ENTRY
(T
RIPLE
F
UNCTION
S
WITCH
):
i. To turn off the blower(s) and the light simultaneously, press this switch once.
ii. After 25 hours of operation, this switch will light to indicate the filters and the blower wheel(s) need to be cleaned in order to maintain
efficient operation of the unit. The switch light will stay on until the function is reset by pressing this switch for 3 seconds.
iii. The light indicator is used for the Heat Sentry function as well.
H
EAT
S
ENTRY
: The power pack is equipped with a protective device that activates when excessive heat is detected inside the power pack
and when it is set on speed
4
. This device takes control of the blower and deactivates speed
4
for a 10-minute period and sets it on
speed
3
. During the Heat Sentry activation, only speed
3
can be used; the Heat Sentry button (
C
) will flash while the speed
3
button
will light. The power pack can also be turned OFF.
D. L
IGHT
S
WITCH
:
This switch allows two different lighting levels according to your needs. Press once for full intensity, twice for nightlight. To shut off the
lights without turning off the blower, press once more.
