Brita TOTAL 360 BRDROS Скачать руководство пользователя страница 7

Страница: 7 / 27

Step A - Install Cold Water Supply Fitting

Cold Water Supply Connection

(using included water supply fitting)

1/4” green

tubing to

Reverse

Osmosis inlet

Check and comply with local plumbing codes as you plan,

then install a cold water supply fitting. Refer to the

Specifications page for supply water requirements. The fitting

must provide a leak-tight connection to the RO 1/4" tubing. A

typical connection using the included water supply fitting is

shown in Figure 6.. An optional connection using standard

plumbing fittings (not included) is shown in Figure 7.

NOTE: Local code may dictate which type of water fit-

ting is used. Consult a plumber if you are not familiar

with local codes or plumbing procedures.
NOTE: Codes in the state of Massachusetts require

installation by a licensed plumber and do not permit the

use of saddle valves.
If you live in the state of Massachusetts, review plumb-

ing code 248-CMR of the Commonwealth of

Massachusetts before proceeding with the installation.

INSTALL COLD WATER SUPPLY FITTING

(Included)

This fitting will be installed on the cold water pipe. The fitting

must provide a leak-tight connection to the Reverse Osmosis

1/4" tubing. Locate the cold water line in the sink cabinet. It

is recommended, but not required, that the cold water line be

soft water.
Complete the following steps to install the water supply fitting.

. Close the water shutoff valve (angle stop valve) that the

water supply fitting will be installed on, and open faucet(s)

to relieve pressure.

. Disconnect the existing cold water line from the water

shutoff valve.

. Make sure that the water supply fitting’s gasket is inside

the female threaded portion of the fitting.

. Install the water supply fitting onto the cold water shutoff

valve, where the existing cold water line was removed,

and hand tighten. Be careful not to cross thread or over-

tighten.

. Connect the existing cold water line to the male threaded

portion of the water supply fitting and hand tighten. Be

careful not to cross thread or overtighten.

OPTIONAL PIPE FITTINGS

(compression type shown)
NOTE:

Be sure to turn off the water supply and open a

faucet to drain the pipe.

Complying with plumbing codes, install a fitting on the cold

water pipe to adapt 1/4" OD tubing. A typical connection is

shown in Figure 7. If threaded fittings are used, be sure to

use pipe joint compound or thread sealing tape on outside

threads.

FIG. 6

Cold Water

Shutoff Valve

CHOOSE TYPE OF WATER FITTING TO INSTALL

Cold Water Supply Connection

(using compression fitting - not included)

FIG. 7

Cold Water

Shutoff Valve

cold

water

pipe

1/4” compression

fitting

insert

ferrule

1/4” green

tubing to

Reverse

Osmosis inlet

cold water

shutoff

cold water

line

water supply

fitting

gasket

Содержание TOTAL 360 BRDROS




























Результаты поиска

Содержание TOTAL 360 BRDROS

Отзывы:

Похожие инструкции для TOTAL 360 BRDROS

Бренды по названию

Популярные бренды

Brita TOTAL 360 BRDROS, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TOTAL 360 BRDROS

Отзывы:

Похожие инструкции для TOTAL 360 BRDROS

Бренды по названию

Популярные бренды