Brita C150KIT-FINEST Скачать руководство пользователя страница 5

bomborasupplies.com.au

[email protected]

1300 724 249

BRITA C150 FINEST

INSTALLATION INSTRUCTIONS

PART #

C150KIT-FINEST

6. Replacing the Filter Cartridge

NOTE:

The C150 filter has a shut-off valve at the filter head.

The replace the filter cartridge:

1.

Rotate the locking handle to divert the water and release the cartridge. Press the flush valve located on the top of the head to depressurise
the filter.

2.

Pull the cartridge downwards to remove, and discard the old filter.

3.

Insert the new filter cartridge ver�cally into the filter head and turn the locking handle un�l you hear it click.

4.

Operate the flush valve and rinse the filter system un�l the filtered water runs clear without carbon fines or bubbles.
This can take up to 2-5 minutes. If your water appears ‘milky’, run the water a little longer. This is caused by �ny air bubbles and is harmless.

NOTE:

A�er carrying out maintenance, we recommend you observe for possible water leaks for a day or so.

HANDY HINT:

To alter tubing, or if a leak occurs at tubing connec�ons, remove tubing from push in connectors by simply holding back the

floa�ng collet around the tube where it enters the quick connect fitting and pull gently on the tubing to remove.
Make sure end of tube is cut square and not distorted. Refit and test.

7. Warranty Informa�on

The C150KIT-FINEST Water Filter System is designed to operate at a maximum pressure of 900kPa (130psi) and at a maximum temperature of 38°C.
Bombora Supplies warrants this system to be free from defects in material and workmanship for a period of Two (2) Years from the date of purchase.
Warranty period excludes cartridges which are consumable.

This warranty is expressly limited to repair or replacement at our premises of any part or parts proving defec�ve providing purifier has been installed
in accordance with our Installa�on Instruc�ons, and that pressure and temperature do not exceed limits stated herein. This warranty does not extend
to mechanical damage. This warranty is given in lieu of all other expressed or implied warran�es or condi�ons and Bombora Supplies will not be held
liable for damages or delays caused by defects. Bombora Supplies will not be held responsible for any unauthorised repairs. Any damage caused by an
unauthorised repairer will void this warranty.

Register your 2-year warranty now by calling 1300 742 249 or log on to our website noted below. Quote the replacement part number of your filter.
Once registered, we will send you a friendly 12-month reminder.

Содержание C150KIT-FINEST






Отзывы: