BriskHeat
®
Corporation. All rights reserved.
HSTAT Silicone Rubber Heating Tapes
BriskHeat
®
Corporation. All rights reserved.
HSTAT Silicone Rubber Heating Tapes
SPECIFICATIONS
4
Operating conditions:
Maximum Exposure Temperature: 450°F (232°C)
Adjustable Thermostat Control 50-425°F (10-218°C)
120 or 240VAC Models
Power Density: 6.0 watts/in
2
(0.009 watts/mm
2
)
Moisture and Chemical Resistant
Suitable for Electrically Conductive Surfaces
120VAC model includes NEMA 1-15 plug
Width
in (mm)
Length
in (mm)
Total
Watts
Part Number
120VAC
Part Number
240VAC
(No plug)
0.5 (13)
24.0 (610)
72
HSTAT051002
HSTAT052002
0.5 (13)
48.0 (1220)
144
HSTAT051004
HSTAT052004
0.5 (13)
72.0 (1830)
216
HSTAT051006
HSTAT052006
0.5 (13)
96.0 (2440)
288
HSTAT051008
HSTAT052008
0.5 (13)
120.0 (3050)
360
HSTAT051010
HSTAT052010
1.0 (25)
24.0 (610)
144
HSTAT101002
HSTAT102002
1.0 (25)
48.0 (1220)
288
HSTAT101004
HSTAT102004
1.0 (25)
72.0 (1830)
432
HSTAT101006
HSTAT102006
1.0 (25)
96.0 (2440)
576
HSTAT101008
HSTAT102008
1.0 (25)
120.0 (3050)
720
HSTAT101010
HSTAT102010
2.0 (51)
24.0 (610)
288
HSTAT201002
HSTAT202002
2.0 (51)
48.0 (1220)
576
HSTAT201004
HSTAT202004
2.0 (51)
72.0 (1830)
864
HSTAT201006
HSTAT202006
2.0 (51)
96.0 (2440)
1152
HSTAT201008
HSTAT202008
2.0 (51)
120.0 (3050)
1440
HSTAT201010
HSTAT202010
3.0 (76)
24.0 (610)
432
HSTAT301002
HSTAT302002
3.0 (76)
48.0 (1220)
864
HSTAT301004
HSTAT302004
3.0 (76)
72.0 (1830)
1296
HSTAT301006
HSTAT302006
3.0 (76)
96.0 (2440)
1440
HSTAT301008
HSTAT302008
3.0 (76)
120.0 (3050)
1440/1800
HSTAT301010
HSTAT302010
STEP 4
Adjust dial to desired setting between 50-425°F (10-218°C).
OPERATING INSTRUCTIONS
Read and understand this entire manual
before operating this electric heating tape.
STEP 1
Remove heater from box. Visually inspect heater. Do not use if torn or damaged.
STEP 2
Installing your heating tape:
The
fl
exible heating tape can be installed on both a
fl
at and/or curved surface.
For a
fl
at surface, lay the heating tape onto the surface to be heated. For a
curved surface, wrap the heating tape onto the surface to be heated. Attach the
heating tape to the surface by using aluminum tape,
fi
berglass tape, or a
mechanical clamping device which will not cause damage to the heating tape.
• The length of one entire side of the heating tape must be in full contact
with the surface. Ensure the heating tape is not kinked, twisted, or any
portion of the tape hanging free from the surface (A).
• Thermostat sensor must be in full contact with object to be heated.
Sensor is located underneath temperature controller box (B).
• Do not overlap heating tape on itself (C).
STEP 3
For 120VAC:
Plug power cord into appropriate outlet.
For 240VAC:
Terminate power cord to appropriate electrical power supply. The
power cable consists of two color-coded conductors, black and white. The black
wire should be connected to Line 1. The white wire should be connected to Line
2. The power connections must be adequately rated to electrically support the
voltage and amperage of the heater. The identi
fi
cation label located on the power
cord displays voltage and amperage requirements.
Correct
Installation:
Incorrect
Installation:
Heating tape
overlapped on itself
Incorrect
Installation:
Heating tape hanging
free from the surface
(A)
(B)
(C)
Temperature controller dial and enclosure will become very hot after use.
Always unplug heater and allow to cool prior to handling.
