© BriskHeat
®
Corporation. All rights reserved.
3
SLCBLSK Splice and Tee Kit
Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
Agency Approvals
Approvals valid only when
installed in accordance with
all applicable instructions, codes, and regulations.
A person who has not read and
understood all operating
Instructions is not qualified to
operate this product.
DANGER
DANGER
Do not immerse splice connection in liquid.
Keep volatile or combustible material away from
splice connection when in use.
Use splice connection only in approved locations.
Keep sharp metal objects away from splice
connection.
Failure to observe these warnings may result in electric
shock, risk of fire, and personal injury.
End-User Must Comply to the Following:
Only qualified personnel are allowed to connect
electrical wiring.
Disconnect all supply power at the source before
making any power connections.
All electrical wiring must follow local electrical
codes and highly recommend following NEC
Article 427.
The person who performs the final installation /
wiring must be qualified for this work.
The end-user is responsible for providing a
suitable disconnecting device.
The end-user is responsible for providing suitable
electrical protection device. It is highly
recommended that a ground fault circuit breaker
be used.
Failure to observe these warnings may result in personal
injury or damage to the product and/or property.
Inspect all components before use.
Do not use splice connection if any component is
damaged.
Do not repair damaged or faulty components.
Do not crush or apply severe physical stress on
any component of system.
Unit must be mounted away from vibration,
impacts, water and corrosive gases.
Do not operate above rated temperature value.
Fasten splice connection using approved
methods only.
Failure to observe these warnings may result in personal
injury or damage to the product and/or property.
CAUTION
WARNING
© BriskHeat
®
Corporation. All rights reserved.
4
SLCBLSK Splice and Tee Kit
Installation Instructions
PRODUCT OVERVIEW
Description
The SLCBLSK Splice and Tee Kit is suitable for use only with the SLCBL series self-regulating heating cable. The kit
contains materials for one splice or one tee connection and one end seal connection. This kit does not provide a power
connection: use a SLCBLUC or SLCBLUC-GF power connection kit for a complete installation.
Applications
Use the SLCBLSK kit with the following heating cables: SLCBL-B, SLCBL-BP and SLCBL-BF. SLCBL-B cable is designed
for pipe freeze protection in dry locations. SLCBL-BP cable is designed for both wet and dry locations, as well as for roof
and gutter de-icing. SLCBL-BF cable is designed for both wet and dry locations, as well as for strong chemical
environments. The cable type is printed on the outer jacket of the cable.
Tools Required
Scissors, Flat nose pliers, Needle Nose Pliers, Utility Knife, Crimp tools,
Cutters, Heat Gun
Kit Contents
Item Qty
Description
A 1
Clamp
tie
B
1
Black cloth tape, 6”L (15.2cm)
C
1
Heat-shrinkable tube, 1”D x 8”L (2.5cm x 20.3cm)
D 3
Cable
ties
E
5
Mastic strips, 1-1/2”L x 1”W, (3.8cm x 2.5cm)
F
3
Heat-shrinkable tube, 1”L x 1/2”D, (2.5cm x 1.3cm)
G
6
Heat-shrinkable tube 1”L x 1/8”D, (2.5cm x 0.3cm)
H 2
Heat-shrinkable
cap
I
2
Insulated bus wire crimps
J
1
Heat-shrinkable tube for ground
K 1
Uninsulated
braid
crimp
Note: Additional Accessories May Be Required.
L
1
End Seal Kit
A B C
D
E
F
G
H
I J K
L
