background image

 

 

 

ChickSafe Eco Door Opener with Door:  Installation and Operating Instructions 

 

IMPORTANT INSTALLATION NOTES! 

 

The door must be attached to the opener BEFORE installing the batteries. Do not fit the batteries until 
the ChickSafe and door are fully installed. 

 

The door must be lifted and held in the open position before attaching the cord. The ChickSafe is supplied 
with the cord wound in ready to be attached to the open door. It will return to this position each time it 
opens. 

 

The door must stop against a solid surface at its closed position. The ChickSafe detects when the weight 
of the door is no longer being supported on the cord and that lets the control know the door is closed. 

 

The distance the door moves between its closed position and open position must be no greater than 
400mm (15 inches). If the door moves down through a greater distance the cord will wind back in again 
and the door will be open even when the ChickSafe shows it is closed (double flashes of the LED light). 

 

Do not remove the knot in the cord that was tied there at the factory. This knot operates the sensing 
device to stop the ChickSafe in the open position. 

 

If using with an alternative door, ensure the maximum door weight of 4kg (8lbs) is not exceeded as this 
will cause damage to the motor and invalidate the guaranty! Note that wooden doors are heavier when 
wet. 

 

Check the sliding door to make sure it runs smoothly and reliably both upwards and downwards. The 
ChickSafe uses gravity alone to close the door. 

 

To mount the ChickSafe further away from the door, an additional length of cord may be attached to the 
end of the internal cord. Do not wind out any cord from inside the ChickSafe. 

 

For helpful information see our ChickSafe ‘Frequently

 

Asked Questions’ page 

and installation videos at 

www.brinsea.co.uk 
 
 

Please read these instructions carefully before setting up your ChickSafe Eco to achieve best results and keep these 
instructions safe for future reference. 

To register your new Brinsea  product and qualify for your free 3 year guaranty  please visit www.brinsea.co.uk 
within 30 days of purchase and follow the link on the Brinsea home page. The serial number may be found on the 
box  and  inside  the  battery  compartment.  Sign  up  for  the  Brinsea  newsletter  to  receive  the  latest  news  and 
information.  

 

Warning - Risk of injury! Keep fingers clear of moving door and cord. Motor may start without warning. 

 

This appliance can be used by children aged from 8 years and above and persons with reduced physical, 

sensory or mental capabilities or lack of experience and knowledge if they have been given supervision 
or  instruction  concerning  use  of  the  appliance  in  a  safe  way  and  understand  the  hazards  involved. 

Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children 
without supervision. 

 

 

CS015 GB Issue 03 

 

Содержание ChickSafe Eco Door Opener








Отзывы: