8
This symbol stands for selective collecting of the electrical and electronic equipment, therefore, this product cannot be treated as other household’s waste.
It has to be left at a special used-equipment collection point. The appropriate dealing with the collection of used electrical and electronic equipment is crucial,
especially if the equipment includes dangerous components which have a negative influence on the environment and on the health of people.
ASSEMBLY
1. Take all the device components out of the packaging and
remove all packaging material and enclosures.
2. Remove the screws from the base parts. Assemble the base
(15) parts together in the shape of a cross.
3. Attach the 4 small feet onto the ends of the base (15).
4. Place the lower pipe (14) with pipe support on the base and fix
it with the four screws provided.
5. Loosen and remove the pipe connector (13) from the lower
pipe (14). Slide the plastic base cover (16) over the lower pipe
on the base. Extend the upper (inner) pipe (12) and slide the
pipe connector (13) over the upper pipe onto the lower pipe and
tighten.
6. Unscrew the knurled bolt (11) but make sure that the hex nut
remains attached on the inside. Attach the motor (7) with
switch compartment (10) onto the upper pipe (12) and tighten
the knurled bolt (11).
7. Loosen the guard mounting ring (4) from the motor housing
(7).
8. Position the rear guard (5) firmly against the motor housing (7)
in such a way that the small hole for the reinforcement screw
is at the bottom of the rear guard, and fasten by turning the
guard mounting ring (4) clockwise tightly.
9. Push the blades (3) along the motor shaft (6). Fasten it firmly
with the blades cap (2) by turning counter clockwise.
10. Hang the front guard (1) to the rear guard (5) and then clamp
together with the clips provided.
11. To ensure that it is impossible to have access to the fan blades
without using a tool, a screw is provided with this appliance
in order to attach both parts of the mesh guard together. This
screw must be tightened with the appropriate hex nut on the
lower part of the guards. We will not be responsible for any
injuries in case this screw had not been tightened before using
the device.
OPERATING THE DEVICE
1. Connect the assembled fan into power socket.
2. This fan is equipped with 3 ventilation speeds. To switch on the
device, press one of the speed knobs. To switch it off, press
“0”.
Speed settings:
- 0 = OFF
- 1 = Low
- 2 = Medium
- 3 = High
3. To change the height, loosen the pipe connector (13) and slide
the upper pipe (12) to a suitable height. Then tighten the pipe
connector again.
4. This device has an oscillation function:
- push the oscillation knob (8) to switch on the oscillation,
- pull the oscillation knob (8) to stop.
5. It is also possible to tilt the upper part of the device in order
to adjust the airflow direction vertically.
CLEANING AND MAINTENANCE
Before cleaning, always switch off and unplug the
device from the mains.
• The device, power cord and plug must not be soaked in water
or other liquids during cleaning. Clean these parts using a dry
cloth.
• When very dirty, the outside of the device can be wiped off
carefully with a damp cloth and subsequently carefully dried.
• Be careful when doing so that no moisture gets inside the
device.
• Do not use any harsh cleaning agent, wire brushes, abrasives
or other hard objects to clean which could scratch the
surfaces.
• Never use solvents, petrol or oil-based cleaners, since these
could damage the housing.
• Clean the device regularly.
CAUTIONS!!
1. We reserve the right to apply changes in the construction
of the product.
2. The information included in this document may undergo
changes without warning. Possible changes will be taken
into consideration while working with other issues of the
instructions for use or complementary documents.
3. We take no responsibility for faults resulting from non-
compliance with the above instructions. According to article
568 pt 1 of the Polish Civil Code, the right resulting from
a warranty for physical defects are extinct after the lapse
of 2 (two) years after delivery of the device to the Buyer.
