Briggs & Stratton Victa Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 28

Briggs & Stratton Victa Скачать руководство пользователя страница 4

Not for

Reproduction

1

QUICK

START

Quick Start Guide

•

That there are no leaks in the fuel system

•

That all screws are securely fastened

• Trimmer Bump Head, Guard and Coupling are secured safely and as

instructed.

Check the position & operation of controls to ensure you are
comfortable before you start using the machine.

Check all components are assembled as per assembly instructions on
page 7.

Quick Start Guide

• Place the trimmer on a hard, level surface.

• Press the PRIMER 10 times.

1 – Get ready…

PRIMER

1.

• Set STOP switch to the “ON” position (I)

• Set the choke lever to COLD

2 – Set

3 – Go!

• Slightly pull out the starter cord until you feel it
resist

• Then tug sharply on the starter cord 2 or 3 times.

• Tug sharply on the starter cord as before.

• 2 or 3 pulls should start your trimer.

Never allow the starter cord to snap back. This may damage the machine!
Repressing the throttle lever will release the throttle lock from the fixed

position.

1.

2.

3.

Check

«
...
2
3
4
5
6
...
»

Содержание Victa





























Отзывы:

Нет отзывов