background image

Not for 

Reproduction

Zero-Turn Riding Mower - 48” Mower Deck

2

 Left side
 shown.

A

B

C

1

2

3

D

A

B

C

 Uncrating

 1.  Pull both transmission release levers (A, Figure 1

back and then down to lock the transmission release 
levers in the disengaged (free-wheel) position. (B)

 2.  Push down the parking brake lever (C) to release the 

parking brake.

 3.  After ensuring there are no nails or sharp objects on 

the bottom skid to puncture the unit’s tires, roll the 
unit forward off the bottom skid.

 4.  After moving the tractor, re-engage the transmissions 

by pulling the transmissions release levers up and 
forward to the engaged (drive) position (D).

 Connect Battery

 1.  Connect the red positive battery cable (A, Figure 2

to the positive battery post.  Make sure that the cable 
boot completely covers the positive terminal, so that 
the terminal cannot cover the insulator pad (B).

 2.  Connect the black negative battery cable (C) to the 

negative battery post.

WARNING

BATTERY SAFETY RULES
• Battery acid causes severe burns. Avoid contact
with skin. 
• Wear eye protection while handling the battery. 
• To avoid an explosion, keep flames and sparks 
away from the battery, especially while charging.
• When installing the battery cables, 
CONNECT THE POSITIVE (+) CABLE FIRST and 
the negative (-) cable last.  If not done in this 
order, the positive terminal can be shorted to the 
frame by a tool.

Figure 1 -  Uncrating the Mower

Figure 2 -  Connect the Battery

Содержание 2900B2548













Отзывы: