Briggs & Stratton 20275 Скачать руководство пользователя страница 18

16

BRIGGSandSTRATTON.COM

5. Make sure garden hose is connected to water inlet.

Check that high pressure hose is connected to spray
gun and pump. Turn on water.

6. Engage trigger lock on spray gun and start engine

following instructions 

How to Start Your Pressure

Washer

.

7. Apply detergent to a dry surface, starting at lower

portion of area to be washed and work upward, using
long, even, overlapping strokes.

8. Allow detergent to "soak in" for 3-5 minutes before

washing and rinsing. Reapply as needed to prevent
surface from drying. DO NOT allow detergent to dry on
(prevents streaking).

IMPORTANT:

You must flush the detergent siphoning

system after each use by placing the filter into a bucket of
clean water, then run the pressure washer in low pressure
for 1-2 minutes.

Pressure Washer Rinsing

For Rinsing:

1. Engage trigger lock on spray gun.
2. Remove black detergent nozzle from nozzle extension.
3. Select and install desired high pressure nozzle following

instructions 

How to Use ProjectPro™ Nozzles

.

4. Keep spray gun a safe distance from area you plan to

spray.

5. Apply a high pressure spray to a small area and then

check surface for damage. If no damage is found, you
can assume it is okay to continue rinsing.

6. Start at top of area to be rinsed, working down with

same overlapping strokes as you used for cleaning.

Cleaning Detergent Siphoning Tube

If you used the detergent siphoning tube, you must flush it
with clean water before stopping the engine.

1. Place detergent siphoning tube/filter in a bucket full of

clean water.

2. Engage trigger lock on spray gun.

3. Remove high pressure nozzle from nozzle extension.

4. Select and install black detergent nozzle following

instructions 

How to Use ProjectPro™ Nozzles

.

5. Flush for 1-2 minutes.

6. Shut off engine following instructions 

How to Stop

Pressure Washer

and turn off water supply.

7. ALWAYS point spray gun in a safe direction and

squeeze spray gun trigger to release retained high
water pressure.

IMPORTANT:

Spray gun traps high water pressure, even

when engine is stopped and water is disconnected.

Automatic Cool Down System (Thermal Relief)

If you run the engine on your pressure washer for
3-5 minutes without pressing the trigger on the spray gun,
circulating water in the pump can reach temperatures above
125°F. The system engages to cool the pump by 

discharging

the warm water onto the ground.

NOTICE

You must attach all hoses before you start the engine.

• Starting the engine without all the hoses connected and without

the water turned ON will damage the pump.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

WARNING

Kickback from spray gun can cause you to fall.

• Operate pressure washer from a stable surface.

• Be extremely careful if you must use the pressure washer from

a ladder, scaffolding, or any other similar location.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks back.

WARNING

The high pressure stream of water that this
equipment produces can cut through skin and its
underlying tissues, leading to serious injury and
possible amputation.

Spray gun traps high water pressure, even when
engine is stopped and water is disconnected,
which can cause injury.

• Keep high pressure hoses connected to pump, hose reel  and

spray gun while system is pressurized.

• ALWAYS point spray gun in safe direction and squeeze spray

gun trigger, to release high pressure, every time you stop
engine. Engage trigger lock when not in use.

Содержание 20275































Отзывы: