Briggs & Stratton 20275 Скачать руководство пользователя страница 14

12

BRIGGSandSTRATTON.COM

How to Start Your Pressure Washer

To start your pressure washer for the first time, follow these
instructions step-by-step. This starting information also
applies if you have let the pressure washer sit idle for at least
a day.

1. Place pressure washer near an outside water source

capable of supplying water at a flow rate greater than
3.8 gallons per minute and no less than 20 PSI at
pressure washer end of garden hose. DO NOT siphon
supply water.

2. Check that high pressure hose is tightly connected to

spray gun and pump. See 

Assembly

section.

3. Make sure unit is in a level position.

4. Uncoil high pressure hose from hose reel completely

before using pressure washer.

5. Connect garden hose to water inlet on pressure washer

pump.

6. Turn ON water, point gun in a safe direction and squeeze

trigger to purge pump system of air and impurities.

7. Attach nozzle extension to spray gun. Tighten by hand.

8. Choose ProjectPro™ nozzle you want to use, pull back

on collar of nozzle extension, insert nozzle and release
collar. Tug on nozzle to make sure it is securely in
place. See 

How to Use ProjectPro™ Nozzles

.

9. Engage trigger lock (

A

) on spray gun trigger.

10. Rotate fuel shut-off valve to “

On

” position (

A

) (fully

counter-clockwise).

11. Move throttle control lever (

A

) to “

High

” position,

shown on engine as a rabbit 

.

12. Move choke lever to “

Choke

” position.

NOTE:

For a warm engine, be sure the choke lever is in the

Run

” position.

IMPORTANT:

Before starting the pressure washer, be sure

you are wearing adequate safety goggles.

13. When starting engine, position yourself as

recommended below and grasp starter grip handle and
pull slowly until you feel some resistance. Then pull
rapidly to start engine.

NOTICE

DO NOT run the pump without the water supply connected
and turned on.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

WARNING

Risk of eye injury.

Spray can splash back or propel objects.

• Always wear safety goggles when using this equipment or in

vicinity of where equipment is in use.

• Before starting the pressure washer, be sure you are wearing

adequate safety goggles.

• NEVER substitute safety glasses for safety goggles.

A

A

A

Содержание 20275































Отзывы: