background image

Operation

14

STARTING THE ENGINE

WARNING

Rapid retraction of starter cord (kickback) will pull
hand and arm toward engine faster than you can
let go. Broken bones, fractures, bruises or
sprains could result. When starting engine, pull
the starter cord slowly until resistance is felt and
then pull rapidly to avoid kickback.

1.

Check the oil level. See “How To Check/Add Oil”
section in Engine Owner’s Manual.

2.

Make sure equipment drive controls, if equipped, are
disengaged. See the equipment manual for location 
and operation of these controls.

3.

Move the throttle control lever (A, Figure 2) to the 
FAST position. Operate the engine with the throttle 
control lever in the FAST position.

WARNING

Unintentional sparking can result in fire or
electric shock.

Unintentional start-up can result in entanglement,
traumatic amputation, or laceration.

• Use a 3-wire extension cord.

• First attach extension cord to electric starter 

connector and then into a wall receptacle. If 
additional extension cord is required, use a 3-
wire.

• If the supply cord is damaged, it must be 

replaced by the manufacturer or its service 
agent or a similarly qualified person in order to 
avoid a hazard.

CAUTION

This engine was shipped from Briggs & Stratton
without oil. Before you start the engine, make
sure you add oil according to the instructions in
the Engine Owner’s Manual. If you start the
engine without oil, it will be damaged beyond
repair and will not be covered under warranty.

WARNING

Engines give off carbon monoxide, an odorless,
colorless, poison gas. Breathing carbon
monoxide can cause nausea, fainting or death.
When starting the engine, start and run engine
outdoors. Do not start or run engine in enclosed
area, even if doors or windows are open.

WARNING

Gasoline and its vapors are extremely flammable
and explosive. Fire or explosion can cause severe
burns or death. When starting the engine, ensure
that spark plug, muffler, fuel cap and air cleaner
are in place and secured. Do not crank engine
with spark plug removed. If engine floods, set
choke (if equipped) to open/run position.

D

C

E

B

F

A

Figure 2. Start/Stop Engine - Manual
A. Throttle Control Lever
B. Fuel Shut-Off Valve
C. Safety Key
D. Choke Control Knob
E. Primer Button
F. Starter Cord Handle 

Содержание 1695303





































Отзывы: