Briggs & Stratton 030430 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 76

background image

44

BRIGGSandSTRATTON.COM

1. Wash the cylinder thoroughly in a solvent such as

kerosene or other commercial solvent.

2. Wash cylinder again using a stiff brush with soap and

hot water.

3. Rinse cylinder thoroughly with hot running water.

4. Repeat washing and rinsing until all traces of honing

grit are gone.

NOTE:

Honing grit is highly abrasive and will cause rapid

wear to all of the internal components of the engine.

When cylinder and crankcase have been thoroughly cleaned,
use a clean white rage to wipe the cylinder bore. If honing
grit is present, it will appear as a grey residue on the rag.
Re-wash and rinse entire cylinder then check again. When
there is no trace of honing grit on the rag, the cylinder is
properly cleaned. Oil the cylinder bore to prevent rusting.

Cleaning Cylinder

Main Bearings

Check Bearings

Main bearings should be replaced if scored or if a plug
gauge (

A

, Figure 59) will enter bearing. Try gauge at several

locations in bearing.

Figure 59

Covers and Sumps

Installation

1. Place seal protector on oil seal.

2. Make sure mechanical governor fear and oil pump

(when used) is engaged with cam gear. Do not for force
cover or sump.

3. Install screws and tighten in sequence shown (Figure

60).

4. Torque screws to values listed in

Engine

Specifications

.

Figure 60

2

1

3

4

5

6

«
...
42
43
44
45
46
...
»

Содержание 030430













































































Отзывы:

Нет отзывов

Похожие инструкции для 030430

Бренд: Coby Страницы: 1

Бренд: LENCO Страницы: 82

Бренд: bem wireless Страницы: 5

Бренд: Listen Technologies Страницы: 7

Бренд: Hytera Страницы: 24

ElectroMate VEC095

Бренд: Vector Страницы: 20

Бренд: Smart Cover Страницы: 12

Бренд: Porter-Cable Страницы: 22

Бренд: La Crosse Technology Страницы: 22

Бренд: Whisper Power Страницы: 19

Бренд: Whisper Power Страницы: 20

Бренд: Whisper Power Страницы: 32

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 4

Бренд: Philips Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды