Briggs & Stratton 030430 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 76

background image

37

Cylinder Head and Valves

Before the cylinder head can be removed, other external parts
must be removed, such as the air cleaner, fuel tank, oil ﬁ ll
tube, blower housing, mufﬂ er, carburetor, control bracket
assembly, and intake manifold.

1. Remove four screws from rocker cover, then remove

cover and gasket (

A

, Figure 44).

Remove Cylinder Head

Figure 44

2. Remove cylinder head screws, then remove head and

gasket from cylinder.

3. Remove push rods one at a time, marking the location

and orientation of each for proper installation later.

NOTE:

On model 210000 the intake push rod (lower, alumi-

num) is hollow and the exhaust push rod (upper, steel) has a
red band of paint for identiﬁ cation.

4. Using a plastic scraping tool, carefully clean all traces

of head gasket from the head and cylinder mating
surfaces.

Disassemble Cylinder Head

1. Loosen rocker arm screws and/or lock nuts, and

remove from rocker arm studs. Remove rocker arms
and rocker balls from studs (

A

, Figure 45).

Figure 45

2. Remove the rocker arm studs.

3. Using thumbs, press down on each valve spring

retainer and disengage retainer (

A

, Figure 46) from

valve stem (

B

). Remove retainers, springs, valves, and

intake valve stem seal/washer, if equipped.

Figure 46

4. Remove push rod cylinder head plate and plate gasket.

Remove and discard the plastic push rod guides from
the head plate.

Inspection

1. Visually inspect head for cracks, excessive heat

discoloration, warping of the cylinder or rocker cover
mating surfaces, and burned or damaged valve seats.
Replace head, if any of these problems are found.

2. If head passes visual inspection, use Plug Gauge

#19122 to check valve guides for wear. If gauge
enters the guide 1/4” (6.4 mm) or more, replace the
entire head. If plug gauge is not available, see

Engine

Specifications

for the valve guide reject dimension.

«
...
35
36
37
38
39
...
»

Содержание 030430













































































Отзывы:

Нет отзывов

Похожие инструкции для 030430

Бренд: Hyundai power products Страницы: 20

Бренд: Mase Generators Страницы: 21

Бренд: A2Z Ozone Страницы: 13

Digital plus LV200

Бренд: Lenz Страницы: 12

Бренд: Whisper Power Страницы: 46

Бренд: Sound Pro Страницы: 8

Бренд: Boston Acoustics Страницы: 2

Бренд: SDI Страницы: 15

Technic 7500 TE C

Бренд: SDMO Страницы: 212

Бренд: Honda Страницы: 45

Бренд: Curtis Страницы: 24

Бренд: Comdel Страницы: 17

guardian II series

Бренд: Datron Страницы: 47

Бренд: GMC Страницы: 24

Бренд: GMC Страницы: 32

Computer MusicMonitor

Бренд: Bose Страницы: 9

Бренд: Bose Страницы: 12

Computer MusicMonitor

Бренд: Bose Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды