Briel motormaher Brielmaier Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 32

Briel motormaher Brielmaier Скачать руководство пользователя страница 25

Here, you will find the oil filler neck and the oil
dipstick for the motor oil

Ideally, the oil dipstick level should correspond
to the marking. In any case, the oil fill must be

situated underneath the max. fill marking
Too much oil or even attaining the „F“ marking
will affect the gas pump’s work

There are different reasons that can be viewed
responsible for an oil temperature increase
(>70

°

C):

• Cooler dirty

• Fan out of work

The latter can also have various causes:

• Thermostat damaged

• Fuse burnt out

• Wire or plug connection damaged

Remove both wires from thermostat and shunt as
shown below, to check whether the thermostat
is damaged:

If the fan continues to run when the ignition is
ON, then the fan, wire and fuse are OK and the
thermostat is damaged.

As preventive measures, check and clean the
cooling ribs regularly and inspect the opening
round of the sparking plug; if necessary, remove
the metal sheet and clean the motor.

Check motor oil level and re-fill

Fan and thermostat

23

Ideal fill

Fuse Thermostat

Sensor for remote

thermometer

«
...
23
24
25
26
27
...
»

Содержание Brielmaier

































Отзывы:

Нет отзывов