breviglieri mini storm 120, Руководство по эксплуатации и техническому обслуживанию

Страница: 22 / 56

- 22 -
mini storm
The transmission components from the overdrive to the pulley
must be aligned after the belt tension has been adjusted.
Loosen the overdrive bolts (1 Fig. 10), lift or lower the overdrive
itself so that the transmission is parallel to the machine, then
retighten the bolts (1 Fig. 10).
Check the planarity of the two pulleys when the belts are regu-
lated or replaced. Place a metal straightedge on the surfaces of
the two pulleys, as illustrated in Fig. 13.
ATTENTION
Comply with the anti-pollution laws when disposing of old oil and
the various components, depending on the type of materials
concerned.
5.2 LUBRICATION
Lubrication of any machine with parts that turn and/or rub together
is a vitally important task for the life and functionality of the actual
machine itself.
Lubrication must therefore be carried out systematically and at
the required intervals.
The frequencies given refer to machine use in a normal environ-
ment. If this machine is used in heavier duty conditions, it must
naturally be lubricated more frequently.
5.2.1 RECOMMENDED LUBRICANTS
- For the overdrive unit, it is advisable to: OLIO AGIP ROTRA MP
SAE 85W/140 or an equivalent type complying with API-GL5/
MIL-L-2105C.
- For all greasing points, the Manufacturer recommends: AGIP
GR MU EP 2 grease or an equivalent type.
When servicing the driveline, strictly comply with the instructions
given by the driveline Manufacturer, in the specific operation and
maintenance manual with which each driveline is equipped.
5.2.2 AFTER THE FIRST 8 HOURS SERVICE
Each new machine must be checked after the first 8 hours serv-
ice. proceed in the following way:
- Check the general condition of the machine.
- After you have checked the hammers/knives for wear, fully
tighten the screws that fix them in place.
- Check to make sure that all the bolts on the machine are tight.
5.2.3 EVERY 20 HOURS SERVICE
- Make sure that the screws that fix the hammers/knives are well
tightened.
- Grease the driveline.
5.2.4 EVERY 100 HOURS SERVICE
- Check the level of the oil in the overdrive housing. If necessary,
top it up through the plug on the top of the gearbox (1 Fig. 16).
5.2.5 EVERY 500 HOURS SERVICE
- Change the oil in the overdrive housing after every 500 hours
service or at least once a year.
5.3 PREPARING FOR STORAGE
Proceed with the following operations at the end of the season or
if the machine is to remain idle for a long period of time:
- Wash the machine and dry it.
- Carefully check the machine and replace any damaged or worn
parts.
- Fully tighten all the screws and bolts, particularly the ones that
fix the knives.
- Thoroughly grease the machine and then cover it with a tarpau-
lin and store it in a dry place.
If these operations are carried out with care, it will be all to
the user’s advantage as the machine will be in optimum con-
ditions when needed again.
5.4 SPARE PARTS
All the parts forming the machine can be ordered from the Manu-
facturer, specifying:
- The machine model.
- The serial number of the machine.
- The year of manufacture.
- The serial number of the required part (indicated in the spare
parts catalogue), a description of the part and the required quan-
tity.
- The means of transport. If this is not specified, the Manufac-
turer will dedicate diligent care to the service but shall not be
liable for delays in shipment due to causes of force majeure.
the shipping costs are always at the consignee’s charge. The
goods travel at the purchaser’s risk and peril even when sold
carriage paid.
Remember that the Manufacturer is always at your disposal
for any assistance and/or spare parts you may required.