8
After all cleaning procedures have been finished, air
the room again for a some time.
Wash your hands thoroughly.
When carefully collecting the glass fragments in a
closed container or bag and storing it outdoors until
its disposal, the mercury will not spread in the room.
There will be no risk to your health.
1. Scope of delivery / Parts overview
(Fig. 1)
B
Plastic plate (6 pcs.)
a) for the right and left side (2 pcs.) (Side plate)
b) for the frontside (1 pc.)
c) for the top side (1 pc.)
d) for the backside (1 pc.)
e) for the bottom side (1 pc.) (Base plate)
C
Small cover plate (1 pc.)
D
Aluminium tube (5 pcs. or 4 pcs.)
E
Aluminium rail (1 pc.) (eventually pre-assembled
to 1b)
F
Screw (10 pcs. or 8 pcs.)
G
Vinyl background (1 pc.)
H
Background paper (2 pcs.)
I
Fixing clips (4 pcs. or 2 pcs.)
J
Lamp socket (2 pcs. or 1 pc.)
1)
Light tube (2 pcs. or 1 pc. - 5600K Daylight DL)
1!
Holder for lamp socket (4 pcs. or 2 pcs.)
1@
Connecting cable (1 pc., included only with two
lamp sockets)
1#
Power cable (1 pc.) with
a) Power plug
b) Plug for lamp socket
c) On/Off switch
2. Assembling the photo box
Fig. 2:
Attach the aluminium tubes (3) and the
aluminium rail (4) to the plastic plate for the right
and left side (1a) and fix them with the screws (5).
Tighten the screws only by hand.
NOTE!
The aluminium rail (4) can be delivered as a pre-
assembled part of the plate for the front side. In this
case, please assemble the rail together with plate
(Fig. 6 can be ignored then).
Fig. 3:
Insert the the plastic plate for the bottom
side (1e). Make sure that the profile sections of the
base plate (1e) match with the cut-outs of the side
plates. Tighten the screws (5) by hand.
Fig. 4:
Move the plastic plate for the backside (1d)
from the top to the bottom through the notches of
the side plates (1a).
Fig. 5:
Insert the plastic plate for the top side (1c).
Fig. 6:
Attach the plastic plate for the frontside (1b)
to the aluminium rail (4).
3. Inserting the background
Fig. 7:
Carefully move the vinyl background (6) from
the front between aluminium rail (4) and base plate
(1e) to the rear. The background will slide along the
backside (1d) to the top side (1c) by itself. It will
form a slightly curved background.
Fig. 8:
Depending on the desired background and
the object, you can add one of the background
papers (7) by pushing it over the vinyl background
(6) in the same way.
Fig. 9:
Use the fixing clips (8) to fix the vinyl
background (6) and the paper background (7) on
the backside (1d).
4. Installing the lighting
Fig. 10
(Assembling step depending on model;
only neccessary/possible with two lamp sockets):
Connect both lamp sockets (9) with each other by
using the connection cable (12).
Fig. 11:
Attach the holders (11) to the lamp sockets
(9). Insert the light tube (10) into the socket, if it was
not assembled in the factory.
Fig. 12:
Open the top side plate and fix the lamp
sockets (9) with the holder clips (11) on the upper
aluminium tubes (3).
Fig. 13:
Put the power plug of the power cable (13b)
through the oval hole of the right or left side plate
(1a).
Fig. 14:
The lamps should be placed in the middle
of the photo box. Put the power plug of the power
cord (13a) into a wall socket after the lamps have
been attached, Use the On/Off switch (13c) to turn
on the light and start your photo shooting.
5. Exchanging the light tube
ATTENTION!
Disconnect the light source from the power
supply (remove plug) before every cleaning and
maintenance!
Fig. 15:
Carefully turn the light tube (10) through
