Breeze33 BZ3310WAC1 Скачать руководство пользователя страница 31

CARE AND CLEANING

Air Filter Cleaning

Note: 

Never use hot water over 40 C(104 F) to cl ean th e

a

  i r fil ter. Never attempt to operate the unit without the air

   filter.

Winter Storage

      If you plan to store the air conditioner during the winter,
      remove it carefully from the window according to the 
      installation instructions. Cover it with plastic or return it to 
      the original carton. 

Cabinet Cleaning

     

     Be sure to unplug the air conditioner to prevent shock or fire 
     hazard. The cabinet and front may be dusted with an oil-free 
     cloth or washed with a cloth dampened in a solution of warm 
     water and mild liquid dishwashing detergent. Rinse thoroughly 
     and wipe dry.
     Never use harsh cleaners, wax or polish on the cabinet front.
     Be sure to wring excess water from the cloth before wiping 
     around the controls. Excess water in or around the controls 
     may cause damage to the air conditioner.
     Plug in air conditioner.

      

TROUBLESHOOTING TIPS

Before calling for service, review this list. It may save your time and expense. This list includes common 
occurrences that are not the result of defective workman-ship or materials in this appliance.

Solution

Air conditioner
does not start

Wall plug disconnected. Push plug firmly into wall outlet.

House fuse blown or circuit breaker tripped. Replace fuse with time delay type or
reset circuit breaker.

Plug Current Device Tripped. Press the RESET button.

Problem

Air from unit does
not feel cold
enough

Set to a Lower temperature.

O

O

Room temperature below 62 F(17 C ). Cooling may not occur until room temperature 

O

O

rises above 62 F(17 C).   

Thermostat set too cold for night-time cooling. To defrost the coil, set to FAN ONLY
mode. Then, set temperature to a Higher setting.

Temperature sensing behind air filter element touching cold coil. Keep it from the cold 
coil.

Air filter may be dirty. Clean filter. Refer to Care and Cleaning section. To defrost,
set to FAN ONLY mode.

Power is OFF. Turn power ON.

Air conditioner 
cooling, but room
is too warm- ice 
forming on cooling 
coil behind 
decorative front.

O

O

Outdoor  temperature below 64 F(18 C). To defrost the coil, set FAN ONLY mode.

Compressor stopped when changing modes. Wait for 3 minutes after set to the COOL 
mode.

30

Push the vent handle to the Vent Closed position 
(where applicable). Open the front panel.
Take the filter by the center and pull up and out.

Wash the filteru sing l iquid d ishwashing d etergent a nd w

  arm

water. Rinse filter thoroughly. Gently shake excess water 
from the filter. Be sure the filter is thoroughly dry before 
replacing. Instead of washing, you may vacuum the filter 
clean.

Содержание BZ3310WAC1

































Отзывы: