background image

2.3

Introduction

Before you start a maintenance service, read the safety precautions and make sure you
have a new service record and all the necessary equipment, tools, and replacement parts
at hand.

2.3.1

Safety Precautions

Follow the safety precautions below when working with the ventilator:

Do not work on the ventilator with the casing removed and the power supply con-
nected, unless the instructions in this manual, or other special service instructions
sent out by Breas, clearly says so.

Always use extreme caution when working with the ventilator connected to the
mains or any other power source and the casing removed.

Do not use explosive gases and/or fluids near the ventilator.

Make sure that all precautions to prevent electrostatic discharge (ESD) have been
taken. Follow all regulations regarding ESD.

NOTE

The Clinician

s Manual contains extended lists of safety precautions.

2.3.2

Service Schedule

Product

Replace the Blower
Assembly

Replace the Battery

Vivo 45

When necessary. The expected lifetime
of the internal battery is 3 years.

Vivo 45
LS

20,000 hours

When the Battery Health parameter is
below 80% (expected lifetime is
approximately 3 years).

Nippy 4

When necessary. The expected lifetime
of the internal battery is 3 years.

Nippy 4+

20,000 hours

When the Battery Health parameter is
below 80% (expected lifetime is
approximately 3 years).

2.3.3

Service Record

The Breas service record is found in Appendices below.

Copy the service record and use it for noting the service checks while performing serv-
ice every second year.

Maintenance Instructions 11

Doc. 007132 D-2

Vivo 45/Nippy 4 Series Service manual

Содержание Nippy 4 Series

































































































Отзывы: