background image

 

FCC:

Any Changes or modifications not expressly approved 

by the party responsible for compliance could void the 

user's authority to operate the equipment. This device 

complies with part 15 of the FCC Rules. Operation is 

subject to the following two conditions:

 (1) This device may not cause harmful interference,

and (2) this device must accept any interference 

received, including  interference that may cause 

undesired operation.

Note: This equipment has been tested and found to 

comply with the limits for a Class B digital device, 

pursuant to  part 15 of the FCC Rules. These limits are 

designed to provide reasonable protection against 

harmful interference in  a residential installation. This 

equipment generates, uses and can radiate radio 

frequency energy and, if not installed  and used in 

accordance with the instructions, may cause harmful 

interference to radio communications. However,  

there is no guarantee that interference will not occur 

in a particular installation. If this equipment does 

cause harmful  interference to radio or television 

reception, which can be determined by turning the 

equipment off and on, the user is  encouraged to try 

to correct the interference by one or more of the 

following measures: 

 

• Reorient or relocate the receiving antenna. 

• Increase the separation between the equipment  

    and receiver. 

• Connect the equipment into an outlet on a circuit  

    different from that to which the receiver is  

    connected. 

• Consult the dealer or an experienced radio/TV  

    technician for help.

 

FCC Radiation Exposure Statement: 

This equipment complies with FCC radiation exposure 

limits set forth for an uncontrolled environment.

This transmitter must not be co-located or operating 

in conjunction with any other antenna or transmitter.

IC:

 

This device complies with ISEDC licence-exempt RSS 

standard (s). Operation is subject to the following two 

conditions:

 

(1) this device may not cause interference, and

 

(2) this device must accept any interference,including 

interference that may cause undesired operation of the 

device.

 

Le présent areil est conforme aux CNR d'ISEDC licables 

aux areils radio exempts de licence.

 

L'exploitation est autorisée aux deux conditions 

suivantes:

 

(1) l'areil ne doit pas produire de brouillage, et

 

(2) l'utilisateur de l'appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage est 

susceptible d'en compromettre le fonctionnement.

ISEDC Radiation Exposure Statement:

This equipment complies with ISEDC RF radiation 

exposure limits set forth for an uncontrolled 

environment. This transmitter must not be co-located or 

operating in conjunction with any other antenna or 

transmitter. Cet appareil est conforme aux 

limitesd'exposition de rayonnement RF ISEDC 

établiespour un environnement non contrôlé.

Cetémetteur ne doit pas être co-implanté oufonctionner 

en conjonction avec toute autreantenne ou 

transmetteur.

Battery

:

CAUTION: RISK OF EXPLOSION IF BATTERY IS 

REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED 

BATTERIES ACCORDING TO THE INSTRUCTIONS.

Содержание BWS















Отзывы: