Bras FBM L Скачать руководство пользователя страница 14

FBM L / LS

14

Bras Internazionale spa

3 -

Do not

 use extension cords to connect the dispenser.

4 -

Do not 

operate the dispenser unless all panels are

restrained with screws.

5 -

Do not

 obstruct air intake and discharge openings: 15 cm

(6”) minimum air space all around the dispenser.

6 -

Do not

 put objects or fingers in panels louvers and faucet

outlet.

7 -

Do not

 remove bowls, augers and panels for cleaning or

routine maintenance unless the dispenser is disconnected

from its power source.

5 OPERATING PROCEDURES

1 - Clean and sanitize the unit according to the instructions in

t h i s   m a n u a l .   S e e   c h a p t e r   5 . 3   C L E A N I N G   A N D

SANITIZING PROCEDURES.

2 - Fill the bowls with product to the maximum level mark. Do

not overfill.

The exact quantity of product (expressed as liters and

gallons) is shown by marks on the bowl.

3 - In case of products to be diluted with water, pour water into

bowl first, then add correct quantity of product. In case of

natural squashes, it is advisable to strain them, in order to

prevent pulps from obstructing the faucet outlet.

4 - To obtain the best performance and result, use bases

designed to be run in Granita freezers. Such bases have a

sugar content of 34 degrees Baumé corresponding to 64

degrees Brix .

For soft drinks the bases are to be diluted with more water,

on a 1 plus 5/5.5 basis.

In any case follow the syrup manufacturer’s instructions for

both Granita and soft drink recipes.

If natural juices (e.g. lemon, orange) as well as sugarless

products (e.g. coffee) are used, dissolve 150 - 200 grams
of sugar per liter.

5 - Install the covers and check that they are correctly placed

over the bowls. There must be a correct electrical
connection between the bowl and the cover.

- Set the control switches as shown in chapter

5.1 DESCRIPTION OF CONTROLS.

7 - Always leave the dispenser on, as the refrigeration stops

automatically when Granita reaches the proper thickness.

The mixers will continue to turn. 

5. 1 DESCRIPTION OF CONTROLS

The dispenser is equipped with a power switch and a light

switch. In addition each bowl is individually operated by a

mixer/refrigeration switch. In fact it is possible to dispense both

soft drinks and Granita.

When a bowl is in Soft Drink mode the beverage temperature

is controlled by the corresponding thermostat.

When a bowl is in Granita mode the mix viscosity is controlled

by the corresponding adjustment screw located in the rear wall

of each container (for temperature and viscosity setting make

reference to chapter 5.2 OPERATION HELPFUL HINTS).

All the switches are located on the faucet side of the dispenser

in switch panels protected by switch covers (see figure 2).

figure 2

In addition all the models except FBM 1 are equipped with an

automatic safety pressure switch to prevent damages to the

compressor. The lighting of the warning light at the left of the

switch covers means insufficient ventilation of the unit. In this

case check that all around the dispenser there is sufficient

space for ventilation, at least 15 cm (6”) on each side and that

condenser filter is free from dust or other obstructions.

In case the warning light is still ON even after these operations

have been carried out, Service call is required. 

With reference to figure 3 dispenser controls functions are as

follows:

figure 3

Power switch (A)

Light switch (E)

Mixer/refrigeration switch (B)

Thermostat (D)

IMPORTANT

However Granita mix may be done, its Brix (sugar

percent content) must be at least 13.

IMPORTANT

Operate the dispenser with food products only.

IMPORTANT

For LS models only: if the covers are not correctly

installed the unit does not run, the mixer does not rotate

and the refrigerator is switched off.

0 position

:

power is turned OFF to all functions.

I position

:

power is turned ON to all functions and the

other switches are enabled. The fan motor

runs.

0 position

:

all top cover lights are OFF.

I position

:

all top cover lights are ON, provided that

power switch (A) is set to I.

I position

:

mixer and refrigeration ON.

SOFT DRINK mode.

0 position

:

 OFF.

II position

:

mixer and refrigeration ON. 

GRANITA mode.

Turn clockwise

: to decrease temperature

Содержание FBM L













































Отзывы: