manualshive.com logo in svg

Bradley HL 200, Инструкция по установке

Поделиться
Скачать
Bradley HL 200 Скачать руководство пользователя страница 10

Bradley Thermostatic Mixing Valve (HL 200) with Optional Cabinet
Model S59-3200 Series

Installation and Maintenance Instructions

10

Bradley Corporation • 215-1299 Rev. H; EN 06-909

1/29/07

S59-3200 Parts Breakdown and Service Kits

O-Ring Kit S65-195

Item Qty.

Description

2

1

O-Ring

14

1

O-Ring

15

1

O-Ring

16

1

O-Ring

19

1

O-Ring

23

2

O-Ring

31

2

O-Ring

33

2

O-Ring

Piston & Liner Kit S65-196

Item Qty.

Description

2

1

O-Ring

3

1

Liner

4

1

Washer

5

1

Screw

6

1

Spring

7

1

Lower Chamber

8

1

Spring

9

1

Washer

10

1

Piston

11

1

Upper Chamber

Thermostat Kit S65-194

Item Qty.

Description

12

1

Thermostat

14

1

O-Ring

19

1

O-Ring

Center Section Kit S65-302

Item Qty. Description

2

1

O-Ring

3

1

Liner

4

1

Washer

5

1

Screw

6

1

Spring

7

1

Lower Overheat 
Chamber

8

1

Spring

9

1

Washer

10

1

Piston

11

1

Upper Overheat
Chamber

12

1

Thermostat

13

1

Pushrod

14

1

O-Ring

15

1

O-Ring

16

1

O-Ring

17

1

Control Cap

18

4

Bolt

19

1

O-Ring

20

1

Top Cap

21

1

Set Screw

22

1

Screw

Check/Stop Kit S65-190

Item Qty.

Description

23

2

O-Ring

24

2

Seat

25

2

Nut

26

2

Washer

27

2

Seal

28

2

Holder (for Seal)

29

2

Spring

30

2

Strainer

31

2

O-Ring

32

2

Stem

33

2

O-Ring

34

2

Cap

NOTE: 

Kit numbers for rough brass finish

and standard range thermostat. Contact
Bradley for other configurations.

Washer/Seal Kit S65-321

Item Qty.

Description

4

1

Washer

9

1

Washer

26

2

Washer

27

2

Seal

Содержание HL 200











Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды