Bradley Express SS Series Скачать руководство пользователя страница 8

Страница: 8 / 17

Express® Lavatory System SS-Series
SS-3/AZ/WH97TAS

Installation - Obsolete

4/24/08

Bradley Corporation • 215-1175 Rev. H; EN 08-805

Installation Instructions continued . . .

Step 3: Install bowl assembly

IMPORTANT: Moving and positioning the bowl will require more than one person.

Note: Refer to Figure 5 below when installing the bowl assembly.

1. With someone to assist you, place the bowl assembly squarely onto the frame.

2. Attach the front of the bowl assembly to the frame using the four 1/4"-20 x 3/8" pan-head

screws and washers provided.

Do not tighten screws at this time.

IMPORTANT: When bolting the bowl assembly to the frame and wall, do not overtight-

en the bolts. Overtightening bolts can damage the Terreon® material.

3. After the bowl assembly is attached to the frame, use two 3/8" bolts and washers (supplied by

the installer) to bolt the bowl to the wall anchors.

4. Tighten the screws installed in procedure #2 above to secure the bowl assembly to the frame.

Do not overtighten.

Installation Instructions continue...

Figure 5

BACK VIEW

Содержание Express SS Series


















Результаты поиска

Содержание Express SS Series

Отзывы:

Похожие инструкции для Express SS Series

Бренды по названию

Популярные бренды

Bradley Express SS Series, Руководство по установке

Результаты поиска

Содержание Express SS Series

Отзывы:

Похожие инструкции для Express SS Series

Бренды по названию

Популярные бренды