INSTALLATION GUIDE
Skylight
5
7
Outside Mount Applications
The back of the mounting bracket must be flush against a flat mounting surface. The
minimum mounting height is specific to the pleat size ordered.
5
/
8
" for
3
/
8
"
pleat or
1" for
3
/
4
" pleat.
From the marks on the wall measure up the minimum height (according to pleat
N
ordered) and mark the bracket locations.
Center each bracket over the previously made mark on the mounting surface.
N
Attach using one or two screws, as necessary.
N
Use a level to check that the brackets are level and aligned.
N
NOTE:
Make sure the headrail brackets and anchor rail brackets are horizontal
and parallel. Make sure the brackets for each rail are aligned at the same height.
INSTALL THE HEADRAIL
NOTE:
Do not remove the rubber bands that hold the headrail, fabric, and
moving rail until after the side tracks are mounted.
With the front (colored) side of the fabric
N
facing you, slide the headrail into the
installation brackets.
Fit the front lips of the brackets into the front
N
groove on the top of the headrail.
Snap the headrail into place.
N
Tighten the tab screw on each bracket until it
N
is snug. Do not overtighten the tab screw.
CAUTION:
Make sure the fabric is not trapped between the headrail and the
installation bracket tabs.
Standard Bracket For
3
/
8
" Pleat Size
Standard Bracket For
3
/
4
" Pleat Size, Double,
And Triple Honeycomb
1"
Minimum
5
/
8
"
Minimum
Tab Screw
Headrail
Installation Bracket
7
Outside Mount Applications
The back of the mounting bracket must be flush against a flat mounting surface. The
minimum mounting height is specific to the pleat size ordered.
5
/
8
" for
3
/
8
"
pleat or
1" for
3
/
4
" pleat.
From the marks on the wall measure up the minimum height (according to pleat
N
ordered) and mark the bracket locations.
Center each bracket over the previously made mark on the mounting surface.
N
Attach using one or two screws, as necessary.
N
Use a level to check that the brackets are level and aligned.
N
NOTE:
Make sure the headrail brackets and anchor rail brackets are horizontal
and parallel. Make sure the brackets for each rail are aligned at the same height.
INSTALL THE HEADRAIL
NOTE:
Do not remove the rubber bands that hold the headrail, fabric, and
moving rail until after the side tracks are mounted.
With the front (colored) side of the fabric
N
facing you, slide the headrail into the
installation brackets.
Fit the front lips of the brackets into the front
N
groove on the top of the headrail.
Snap the headrail into place.
N
Tighten the tab screw on each bracket until it
N
is snug. Do not overtighten the tab screw.
CAUTION:
Make sure the fabric is not trapped between the headrail and the
installation bracket tabs.
Standard Bracket For
3
/
8
" Pleat Size
Standard Bracket For
3
/
4
" Pleat Size, Double,
And Triple Honeycomb
1"
Minimum
5
/
8
"
Minimum
Tab Screw
Headrail
Installation Bracket
9
Outside Mount
The narrow flange on the side tracks should be at the front of the shade. Holes are
drilled in the groove near the edge of the wide flange.
Attach the wide flange to the outside of the window casement using the
N
appropriate fasteners.
Measure the distance between the side rails at the top and bottom of the window
N
to make sure the rails are parallel.
INSTALL THE ANCHOR RAIL
CAUTION:
Be careful not to tangle the cords.
Cut the rubber bands that are holding the rails and fabric together.
N
Lower the anchor rail to the bottom of the side tracks.
N
Make sure the open side of the anchor rail faces up, with the spring and
N
cords exposed.
If the open side is covered by a fabric strip, remove it to make any
N
shade adjustments.
Outside mounts:
N
Snap the anchor rail into the installation brackets.
Inside mounts:
N
Attach the anchor rail directly to the sill.
Center the rail within the side tracks before mounting.
N
Top View:
Narrow Flange
At Front
Window
Casement
Attach Screw
Through Holes
In Drill Groove
Attach the anchor rail directly to the sill.
Center the rail within the side tracks before mounting.
