Bradford White LC2PDV50H76 Скачать руководство пользователя страница 3

Condensing PDV Series

  

 

WARNING:

If the information in these

instructions is not followed exactly, a fire or

explosion may result causing property damage,

personal injury, or death.

FOR YOUR SAFETY

   Do not store or use gasoline or other flammable, 

combustible, or corrosive vapors and liquids in the 

vicinity of this or any other appliance.

IMPORTANT

Before proceeding, please inspect the

water heater and its components for

possible damage.

DO NOT

install any

water heater with damaged

components. If damage is evident

then please contact the supplier where

the water heater was purchased or the

manufacturer listed on the rating plate

for replacement parts.

 

 

 

 

 

 

 

WHAT TO DO IF YOU SMELL GAS: 

x

 

DO NOT try to light any appliance. 

x

 

DO NOT touch any electrical switch; do not use any 

         phone in your building. 

x

 

Immediately call your gas supplier from a neighbor's phone.  

Follow the gas supplier's instructions. 

x

 

If you cannot reach your gas supplier, call the fire 

 department. 

Installation and service must be performed by a qualified 

installer, service agency or the gas supplier. 

 

 

DANGER 

DO NOT store or use gasoline or other 

flammable, combustible, or corrosive vapors 

and liquids in the vicinity of this or any other 

appliance. 

 

WARNING 

DO NOT ATTEMPT TO LIGHT ANY GAS APPLIANCE IF YOU ARE 

NOT CERTAIN OF THE FOLLOWING: 

x

 

Liquefied petroleum gases/propane gas and natural gas 

have an odorant added by the gas supplier that aids in the 

detection of the gas. 

x

 

Most people recognize this odor as a “sulfur” or “rotten egg” 

smell. 

x

 Other conditions, such as “odorant fade” can cause the 

odorant to diminish in intensity, or “fade”, and not be as 

readily detectable. 

x

 

If you have a diminished sense of smell, or are in any way 

unsure of the presence of gas, immediately contact your gas 

supplier from a neighbor’s telephone. 

Gas detectors are available.  Contact your gas supplier, or plumbing 

professional, for more information. 

 

CAUTION 

Turn OFF or disconnect the electrical power supply to the water heater 

before servicing.  Label all wires prior to disconnection when servicing 

controls.  Wiring errors can cause improper and dangerous operation.  

Verify proper operation after servicing. 

 

WARNING 

FAILURE TO INSTALL AND MAINTAIN A NEW, LISTED ¾” X ¾” 

TEMPERATURE AND PRESSURE RELIEF VALVE WILL RELEASE 

THE MANUFACTURER FROM ANY CLAIM THAT MIGHT RESULT 

FROM EXCESSIVE TEMPERATURE AND PRESSURES. 

 

WARNING 

Water heaters are heat producing appliances.  To avoid damage 

or injury, do not store materials against the water heater or vent-

air intake system.  Use proper care to avoid unnecessary contact 

(especially by children) with the water heater and vent-air intake 

components.

  UNDER NO CIRCUMSTANCES SHOULD 

FLAMMABLE MATERIALS, SUCH AS GASOLINE OR PAINT 

THINNER BE USED OR STORED IN THE VICINITY OF THIS 

WATER HEATER, VENT-AIR INTAKE SYSTEM OR IN ANY 

LOCATION FROM WHICH FUMES COULD REACH THE 

WATER HEATER OR VENT-AIR INTAKE SYSTEM 

 

WARNING 

Hydrogen gas can be produced in an operating water heater that 

has not had water drawn from the tank for a long period of time 

(generally two weeks or more).  

Hydrogen gas is extremely 

flammable.

 To prevent the possibility of injury under these 

conditions, we recommend the hot water faucet to be open for 

several minutes at the kitchen sink before you use any electrical 

appliance which is connected to the hot water system. If 

hydrogen is present, there will be an unusual sound such as air 

escaping through the pipes as hot water begins to flow. DO NOT 

smoke or have open flame near the faucet at the time it is open.

 

 

CAUTION 

If sweat fittings are to be used DO NOT apply heat to the nipples 

on top of the water heater.  Sweat the tubing to the adapter 

before fitting the adapter to the water connections.  It is 

imperative that heat is not applied to the nipples containing a 

plastic liner.

 

3

Содержание LC2PDV50H76













































Отзывы: