Bradford White Condensing PV Series Скачать руководство пользователя страница 15

Страница: 15 / 44

Troubleshooting

Condensing PV Series

LED Status

Control Status

Probable Cause

Service Procedure

Six-one flash,

three second

pause

Failed to light
pilot.
System auto

resets.

1. Unstable pilot.
2. Pilot tube blocked or restricted.
3. Oxidation build up on pilot electrode.
4. Wire damage to pilot assembly or bad

connection at gas valve.

5. Low gas pressure.

Page 18

Six-two flash,

three second

pause

Pressure switch
or blower temp
switch opened
during burner
operation.
System auto

resets.

1. Vent blockage or improper vent

configuration.

2. Pressure switch tubing kinked or blocked.
3. Faulty pressure switch.
4. Vent termination being affected by wind.
5. Blower not spinning up to speed.
6. Blower temp or exhaust temp too high.
7. Faulty blower temperature switch.

8. Blocked condensate trap.

1. Check vent or vent

tables.

2. & 3. Page 19
4. Refer to venting

section of
installation manual.

5. Page 21
6. & 7. Page 23

8. Page 39

Six-three flash,

three second

pause

Pilot flame
extinguished.
System auto

resets.

1. Unstable pilot.
2. Pilot tube blocked or restricted.
3. Oxidation build up on pilot electrode.
4. Wire damage to pilot assembly or bad

connection at gas valve.

5. Insufficient combustion air.
6. Gas pressure is out of specification.

1.-4. Page 18

5. Refer to installation

manual

6. Page 25

Six-four flash,

three second

pause

Undesired-false
pilot flame
sensed.
System auto

resets.

Pilot valve stuck in open position.

Replace gas control,
page 27

Seven flash,

three second

pause

Simulated

Resistive Device

fault detected.

Simulated resistance device harness out of

specification or disconnected.

Page 29

Eight-one flash,

three second

pause

Simulated

Resistive Device

out of

specification.

Simulated resistive device out of

specification. Possible short.

Page 29

Eight-two flash,

three second

pause

Temperature

sensor fault.

1. Damage to temperature sensor wire.
2. Temperature sensor resistance out of

range.

Page 27

Eight-three flash,

three second

pause

Gas valve

electronics fault

detected.

1. Control needs to be reset.
2. Control is wet or physically damaged.

1. Interrupt power

supply.

2. Replace gas control,

page 27

Eight-four flash,

three second

pause

Gas valve fault

detected.

1. Control needs to be reset.
2. Control is wet or physically damaged.

1. Interrupt power

supply.

2. Replace gas control,

page 27

Содержание Condensing PV Series













































Результаты поиска

Содержание Condensing PV Series

Отзывы:

Похожие инструкции для Condensing PV Series

Бренды по названию

Популярные бренды

Bradford White Condensing PV Series, Руководство по обслуживанию

Результаты поиска

Содержание Condensing PV Series

Отзывы:

Похожие инструкции для Condensing PV Series

Бренды по названию

Популярные бренды