background image

14

Parameters

 

Per channel: Switch on the ON/OFF delay, staircase 

lighting function and disable function.

Channel X: General
Parameter

Setting

Disable function

switched off
switched on

ON delay

switched on
switched off

OFF delay

switched on
switched off

Staircase lighting function

switched off
switched on

 

Per channel: Set the disable function.

Channel X: Disable
Parameter

Setting

Disable function for

Disable object = 0
Disable object = 1

Value of disable object after bus 

voltage recovery

1
0

Reaction at blocking

no change
changes state
actuated
not actuated
flashes

Reaction at activation

no change
follows switch object
actuated
not actuated

Reaction at activation (with active 

staircase lighting function)

follows switch object
not actuated

 

Per channel: Set the ON and OFF delay.

Channel X: Times
Parameter

Setting

Time base for ON delay -

100 ms
1 s
1 min
1 hr

Factor for ON delay 

(1-255)

3 

adjustable in single steps

ON delay is

not retriggerable
retriggerable

Time base for OFF delay -

100 ms
1 s
1 min
1 hr

Factor for OFF delay 

(1-255)

120 

adjustable in single steps

OFF delay is

not retriggerable
retriggerable

 

Set the flashing interval for the device if required.

Flashing interval
Parameter

Setting

Flashing interval base

100 ms
1 s
1 min
1 hr

Flashing interval factor [5-255]

10 

adjustable in single steps

L

L

Important 

No short switching times may be parameterised 

under load (see the technical data for the switch 

output)

 - Disable function with switching delay/staircase light-

ing function
When the disable function is activated, it always switches 

in the required direction without a delay. When it is deacti-

vated, the actuator likewise switches to the required state 

without a delay. The last switching telegram is saved during 

a disable function and any delay periods or staircase timers 

continue to run. 

Disable function for: Disable object = 1; Value of disable object after bus 
voltage recovery: 0; Reaction at blocking: no change; Reaction at activa-
tion: follows switch object: Relay: make contact

Communication objects
The following communication objects can be selected:
Per channel:

Function

Object name

Type

Prio

Flags

Behaviour

Channel X

Switch object

1 bit

Low

CW

Receive

Channel 1, 

2,...

Disable object

1 bit

Low

CW

Receive

KNX

telegram,

switch object

t

t

Relay status

closed

1

open

1

t staircase

t staircase

1

t staircase

KNX

telegram,

disable object

t

1

0

1

0

1

0

disabled

disabled

disabled

Содержание KX12O16A





















Отзывы: