background image

www.hanmey.com.au

 

7

 

   OPERATION 

 

 

 

 

2.1  CHECKING BEFORE OPERATING

 

The Log splitter will fit most Category 1 tractors equipped with a standard 3-point hitch. The pins 
need to be installed to the inside of the 3-point frame for use with Category 1 tractors, This Implement 
is designed for use on tractors must be equipped with remote hydraulics

 

 

Check the tractor’s 3-point hydraulic lift system.

 

It should operate up and down smoothly and hold its position when set.

 

Refer to your tractor owner’s manual or dealer for any adjustments necessary to put the 3-point 
hydraulic lift system in good working order.

 

Tractor should be equipped with stabiliser bars, adjustable sway chains, or sway blocks to keep the 
implement from swinging side to side.

 

Smaller size tractors may need front counter weights to counter-balance the weight of the 
implement.

 

 

2.2  ASSEMBLY AND MOUNTING

 

 

1.  Lower the hydraulic linkage arms using the position control.

 

Note:

It may be necessary to add weight to the three points hitch to lower the lift arms.

 

2.  Back the tractor at low speed towards the Implement and adjust the lower links to the proper 

level.

 

3.  Stop tractor, set park brake, remove ignition key and wait for all moving parts to stop before 

dismounting.

 

4. 

Connect the tractor’s lower links with implement’s left and right lower suspension bracket and 
put pins in. Connect the chain top-

link with implement’s top-link bracket and put pin in.

 

5.  Connect hydraulic couplers to tractor remotes, use the 3 points hitch to raise the machine from 

the ground before moving the machine.

 

6.  Reverse the above procedure when removing the machine from the tractor.

 

 

2.3  Field operation

 

 

1.  Position the Log Splitter on solid level ground when operating.

 

2.  Apply the tractor brake securely and put transmission into Park / Neutral.

 

3.  Using right hand to select direction of movement.

 

4.  Operate ram to lift wedge above height of log to be split.

 

5.  Position centre of log under wedge. Move wedge until contact is made with the log.

 

6.  Keep two hands on control levers while splitting log. The speed can be controlled by how much 

pressure you put on the control valve.

 

7.  Stop splitting if log starts to go sideways and reposition per above instructions.

 

8.  Should the wedge lodge or become stuck in the log, return wedge to fully open position and 

gently rock log free before continuing.

 

 

2.4  Transporting

 

When transporting the machine, review and follow these instructions:

 

1.  Be sure that the machine is securely attached to the tractor and all retainer pins are installed.

 

2.  Be sure you have installed extra weights on the front of the tractor.

 

3.  Be sure you are in compliance with all applicable lighting and marking regulations when 

transporting.

 

4.  Be sure your machine can be seen clearly by overtaking and oncoming traffic.

 

5.  Do not allow riders.

 

6.  Always use hazard flashers on the tractor when transporting.

 

Содержание LSP22T
















Отзывы: