background image

01 

 

SUPERMATCH SPORTING 

 

DOUBLE 

 

INSTRUCTIONS

 

 

WJ Bowman

 

High Street East Markham 

 

Nottinghamshire NG220RE

 

01777 870243

 

www.bowmantraps.co.uk

 

@bowmantraps 

 

 

Thank you for your purchase, please call if you need any help or advice. Your support online would be 
much appreciated. Kind Regards Andrew Davidson Managing Director of WJ Bowman (1884) LTD. 

 

Check Contents

 

Having moved the protective card from around the clay pigeon trap, check its contents to ensure they are 
all present. You should have included:

 

• 

1 x Trap fixed to a pallet

 

• 

1 x Safety Ring

 

• 

1 x Coil of 50m cable and button unit / or wireless radio remote (if purchased)

 

• 

Bowman barrow (if purchased with the trap)

 

Positioning and fixing clay pigeon trap

 

Your clay pigeon trap can be fixed onto and operated from a pallet however, we could recommend a more 
permanent bolted position or a Bowman barrow. If you have purchased a barrow position the trap onto the 
barrow and line up the 3 bolt holes. Use the 12mm bolts provided to secure your trap to the barrow. A 
washer should be placed on either side, a spring washer goes on before the nut to secure.   

 

Key Points:

 

 Check your contents

 

 Read thoroughly before 

attempting to assemble or 
operate.

 

 Do not attempt to fit the battery 

until all three assembly tasks 
have been completed!

 

Think! Safety First!

 

These machines can cause serious injury, please read 
instructions prior to assembly and use.

 

If you are missing any contents, are unsure or concerned 
about the use of your clay pigeon trap don

t hesitate to call 

Bowman

s directly on 01777 870243. 

 

Tools Required: 1 x 17mm spanner, 2 x 19mm spanners & 
wire cutters / scissors.

 

Содержание SUPERMATCH SPORTING DOUBLE







Отзывы: