background image

1

8027822.081520.A

8027821.081520.A

Service Manual

Table of Contents

Bowflex

 SelectTech

 2080 Barbell with Curlbar

Service Manual

Section Code 

 

Section  

Page Number

 

Important Safety Instructions 

2

 

Safety Warning Labels and Serial Number 

3

 

Specifications 

3

 

Moving the Equipment 

4

 

Leveling the Base 

4

 1 

Maintenance 

4

       1 

Maintenance Parts 

5

 

Troubleshooting  

6

 

Testing the Locking Mechanism 

7

 

Replacement Procedure Skill Level 

8

 

            Mechanical / Modification Procedures

 

Align the Base 

9

 

            Part Replacement

 

Replace the Selection Knob and Housing 

13

 

Nautilus, Inc., www.NautilusInc.com, 5415 Centerpoint Parkway, Groveport, OH 43125 U.S.A. - Customer Service: North America (800) 605-3369, [email protected] | outside U.S. www.nautilusinternational.com | 

Printed in China | © 2020 Nautilus, Inc. |  Bowflex, the B logo and SelectTech are trademarks owned by or licensed to Nautilus, Inc., which are registered or otherwise protected by common law in the United States 

and other countries. | 

ORIGINAL DOCUMENT - ENGLISH VERSION ONLY

Содержание SelectTech 2080
















Отзывы: