manualshive.com logo in svg

Boulevard LS60THF-1 DVLL60BP90N-1, Инструкция по установке и руководство пользователя, Страница: 52 / 64

Поделиться
Скачать
Boulevard LS60THF-1 DVLL60BP90N-1 Скачать руководство пользователя страница 52

35662-3-0216

Page 52

COMPONENT WIRING DIAGRAM

If any of the original wire as supplied with this fireplace must 

be replaced, it must be replaced with equivalent gauge and 

temperature rated wire.

This fireplace is only for use with the type of gas indicated 

on the rating plate and may be installed in an aftermarket, 

permanently located, manufactured (mobile) home where not 

prohibited by local codes. This fireplace is not convertible for 

use with other gases, unless a certified kit is used.

 

WARNING

Electrical Grounding Instructions

This fireplace is equipped with a three-prong grounding plug for 

your protection against shock hazard and should be plugged 

directly into a properly grounded three-prong receptacle. Do 

not cut or remove the grounding prong from this plug.

 

CAUTION

Label all wires prior to disconnection when servicing controls. 

Wiring errors can cause improper and dangerous operation.

 

CAUTION

Do not operate the fireplace with glass panel removed, cracked 

or broken. Replacement of the panel should be done by a 

licensed qualified service person.

 

WARNING

Improper installation, adjustment, alteration, service or 

maintenance can cause property damage, personal injury or 

loss of life. Installation and service must be performed by a 

qualified installer, service agency or the gas supplier.

Verify proper operation after servicing.

ORANGE

PILOT

GAS CONTROL VALVE

ORANGE

GREEN

YELLOW

WHITE

OR

BLACK

BLACK

WHITE

BLOWER

FUSE

BLACK

WHITE

GREEN

TO JUNCTION

BOX

AUX.

LOOP

TO LIGHTS

SLEEV

E

USER INTERFACE/

BATTERY HOLDER

ORANGE

WHITE

Содержание LS60THF-1 DVLL60BP90N-1

































































Отзывы:

Нет отзывов