manualshive.com logo in svg

Boulevard LS60THF-1 DVLL60BP90N-1, Инструкция по установке и руководство пользователя, Страница: 19 / 64

Поделиться
Скачать
Boulevard LS60THF-1 DVLL60BP90N-1 Скачать руководство пользователя страница 19

35662-3-0216

Page 19

Once the Junction box has been installed with the receptacle 

outlets facing inward towards the fireplace, locate the 3-prong 

power cord from the control module and plug into the receptical.

The fireplace is supplied with a User Interface wall box that must 

be installed in a standard plastic outlet box (not provided). A low 

voltage orange or blue box is recommended. The user interface 

wall box must be placed in the wall within ten feet from the right 

side of the fireplace. A 10ft. battery and user interface extension 

wire harness is supplied.

The red and black battery extension harness must be connected 

to the red and black mating connector pre-installed on the control 

module. The mating connector can be located inside the fireplace 

below the gas valve. See Figure 22.

The user interface extension wire harness must be routed 

through the lower rectangular opening below the gas valve. Plug 

the white connector into the mating user interface connection on 

the control module. See Figures 21, 22 and wiring diagram on 

page 52.

Locate and install the 5/8in diameter plastic snap-in grommet 

over the low-voltage battery and interface extension harnesses at 

the right side of the fireplace. Snap the grommet into the hole in 

the side of the fireplace just under the access panel opening. See 

Figure 22.

Run the extension wiring to the user interface wall box and 

connect the white connector to the remote receiver battery box. 

Install the battery box into the wall outlet box, then install the 

white remote cover supplied with the provided screws.

Figure 21

HAND BENT

FLANGE

ROUTE WIRE HARNESS UNDER THE HAND
BENT FLANGE, THROUGH THE OPENING
OVER TO THE CONTROL MODULE. CONNECT
THE WHITE 4-WIRE HARNESS TO THE “USER

INTERFACE” LOCATION

WIRE

GROMMET

USER INTERFACE HARNESS

& BATTERY EXTENSION

HARNESS

CONNECT TO THE USER INTERFACE/BATTERY
HOLDER. MUST BE INSTALLED IN A WALL
JUNCTION BOX (ORANGE LOW VOLTAGE OR
BLUE BOX RECOMMENDED)

NOTE: OUTER ACCESS DOOR REMOVED. REPLACE AFTER ALL

WIRE AND GAS CONNECTIONS HAVE BEEN MADE

Figure 22

ELECTRICAL CONNECTIONS

Содержание LS60THF-1 DVLL60BP90N-1

































































Отзывы:

Нет отзывов