Setting and Operations
Setting and Operations
<Manual Scan>
1.
If you press
OK
in Manual Scan of
Installation Menu, the
<screen 5>
will be
appeared.
2.
Use the
Up/Down
button to select the item,
and set up the parameter with the
Left/Right
button.
3.
If you completed setting use Red(TP Scan)
button to scan current transponder channel,
G r e e n b u t t o n t o e n t e r P I D s c a n m o d e ,
Yellow button to edit TP information, Blue
button to go to Antenna Setup menu.
TP Scan
: Searches channels from a specific
transponder.
PID Scan
: You can search a specific channel
by entering the PID value of a
channel.
<screen 5>
If you press Green(PID) button, the PID
screen is displayed as below.
Enter the PID value and press the PID button
again.(To cancel the PID value, press Exit on
the remote controller, or press the Blue(PID)
button to search the channel. You should
enter V-PID, A-PID, and P-PID)
<screen 6>
<Timer Setting>
You can set the time to make the receiver
perform the designated actions including
timer based recording(VCR), wake up/sleep
the set-top-box.
You can see the current setting state of all
timers.
1.
If you press
OK
in Timer Setting of Installation
Menu, the
<screen 8>
will be appeared.
TP Edit
: If you press Yellow button You can
edit the TP value. Press
OK
in the
Add item to add the new TP value,
in the Modify item to change the
current value, in the Delete item to
delete the current TP value.
<screen 8>
<screen 7>
14
15
<screen 9>
Use the
Up/Down
button to select the item,
and change the parameters using
Left/Right
button. If you completed timer settings, use
Red(Save) or Green(Save&Exit) button to
save timer setting.
Timer Number
: You can select up to 8 timers.
Timer State
: You can make this state Enabled to use the timer function.
Timer Cycle
: You can set the cycle of the action designated in the timer mode.
Timer Service
: You can set the service(Sleep, Wake up, VCR Record) of the action
designated in the timer mode.
Date
: You can set the starting date of the timer action.
If you press
OK
, calendar is displayed.
Start Time(sleep time/wakeup time)
: You can set the starting time of the timer action.
Ending Time
: You can set the ending time of the recording when the Timer mode is
VCR Record.
Channel
: You can select the program channel recorded when Timer mode is VCR
Record. When Timer service is wake up, this channel is viewed receiver
is powered on by timer function.
4.3 TV menu at the normal mode(No menu state)
At normal mode, various menus are
displayed on the screen with remote
control action. You can change the
current status and mode with various
buttons including the
Up/Down
,
SAT
,
INFO
and
EPG
button.
<Screen 10>
shows the banner displayed when
you press the
INFO
button. If you
the button again before the
banner on the upper part of the screen
is disappeared, another banner is
displayed on the bottom of the screen.
The bottom banner shows information
on the current channel.
press
<screen 10>
TV/Radio mode
Channel number
Current time
Cannel information
PID
Signal level/Quality
Event time
Event name
Sound
Channel name
Subtitle
Teletext Scramble AC3 Audio
50%
80%
-
MUTE
: Mutes the current channel audio.
-
POWER
: Turns the receiver power on/off.
-
SOUND
: Sets the current channel audio to stereo/left-mono/right-mono.
-
TV/RADIO
: Changes the current mode. If you press the
Radio
button at TV mode,
the system changes into the Radio mode, and if you press the
TV
button
at Radio mode, the system changes into the TV mode. And if you press
the
TV
button at the TV mode, or the
Radio
button at the Radio mode,
the TV/Radio list menus are displayed. (The menus are the same as
those of Channel Manager, but are not available to edit. To edit, use the
Channel Manager of the Main menu.)
2.
Use the
Up/Down
button to select the
timer, and press
OK
button to setup
selected timer information. Following
screen will be displayed.